AVR 单片机IIC程序

请认真阅读您的文件包然后写出其具体功能(至少要20个字)。尽量不要让站长把时间都花费在为您修正说明上。-Please read them carefully before you write the document package to their specific functions (at least 20 words). As far as possible not to let the station to the time spent on your note on the amendment.

TI DSPF2812外部中断源码,-TI DSPF2812 external interrupt source,

此代码使用计时器产生一个500khz的方波。 主程序运行的同时，在后台运行的计时器。

44B0开发板上实现PS2接口键盘的程序，对初学者很有帮助-44B0 development board to achieve PS2 keyboard interface procedures helpful for beginners

硬件系统模块包括超声波收发模块、LED显示模块、声光报警模块、STC89C52单片机模块。软件主程序流程图包括主程序流程图，定时中断子程序流程图，外部中断子程序流程图。如果距离小于一定数值，则会进行蜂鸣器报警，同时每个方向对应一个LED灯，报警时对应的LED会亮。采用两个测距模块，更加提高了倒车时的安全性，降低了事故的发生率。

MPC860 UPM口的应用，内有具体应用分析，适用于BSP的开发-MPC860 the application within a specific application analysis, applicable to the development of BSP

开发环境:ADS 1.2/SDT 2.51 GUI测试，由于没有触摸屏，所以将触摸屏的代码给屏蔽了； 请将FS44B0II开发板连接好交叉网线、直连串口线、电源， 并连接好G57液晶屏，同时还要连接好背光电源； 然后在BIOS的命令窗口里面敲netrun命令； 点击FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel目录下： 批处理文件FS44B0_G57_uCGUI.BAT 下面你就可以看到液晶屏上面显示优龙标志 它会延时一两秒中进入下一个画面，逐步延时GUI的各项功能，请耐心观看； -Development Environment: ADS 1.2/SDT 2.51GUI test, because there is no touch screen, it will be touch screen to shield the code Please FS44B0II development board to connect a good cross-network lines, direct serial lines, power supply, and connect a good G57 LCD screen, at the same time, good backlight power supply connection and then in the BIOS command window knock netrun order Click FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel directory: batch file FS44B0_G57_uCGUI.BAT below you can see the LCD screen above shows excellent signs that it will delay Liuzhou 1 two seconds to enter the next screen, and gradually delay the GUI features, please be patient watch

DS1302读写程序，经下载检验完全可用。-DS1302 to read and write procedures for testing fully available by download.

一个uCOS-II下的tcpip协议栈实现，可用于嵌入式系统的网络应用开发-a uCOS-II under the TCPIP stack, which could be used in embedded system development of network applications

远程抄表系统程序，是电力线载波通信的，用汇编编写。