IC卡操作Demo 包括了常见的IC卡种类。可执行写入、读出、校验、密码修改、批量作业等功能。

ADS7843的应用。用来做触摸屏。是不错的东东。拿来可用-ADS7843 applications. Used to make touch screen. Is a good Dongdong. Use of available

这是一个用abel语言编写的步进电机程序-This is a language used abel stepper motor procedures

该文件是采用通用IO口模拟I2C存储器通讯的,24LC256是低电压I2CEEPROM.-this document is to adopt a common IO memory simulation I2C communications, 24LC256 is low voltage I2CEEPROM.

x5045有四种功能：分别是上电复位、看门狗定时器、电源电压监控和块锁保护串行eeprom的功能， 该程序通过改变控制寄存器的参数可以实现看门狗定时器监视电压和设置保护rom区，每次复位后 地址计数器都是该区的首地址（个人观点），即断点地址。 问题：其实对该芯片的应用还是很模糊-x5045 four functions : the reduction of electricity, watchdog timer, Supply voltage control and protection block serial eeprom lock function, The procedure by changing the parameters of control register can be achieved watchdog timer and set up surveillance voltage protection rom, After each reset address counter area is the first address (personal view), breakpoint address. Question : In fact, the application of this chip is still very fuzzy! !

JUPITER演示程序，uart串口通信-JUPITER demo, uart serial communication

51单片机控制ISD1420实现选段播放功能的实现-ISD1420 single-chip implementation of 51 selections to control playback of the implementation

谐波计算，用用也不错，大家可以试一试。不好用也别找我啊-Harmonic basis, with use it as well, everyone can try. Bad do not use me ah

仔细详细的介绍了msp430单片机的各个寄存器，对初学者相当的有用-Carefully detailed introduction of the MSP430 MCU in all registers, very useful for beginners

功能：利用时钟芯片DS12887在LCD（LCM141）上显示时间，通过4×4键盘来修改时间，利用MAXIM232进行标准串口发送。4×4键盘中有数字键（0～9）和功能键（F1键为“→”，F2键为“←”，F4键为“发送”，设置键为“设置当前时间”，确定键为“把修改的当前时间写入到DS12887相应的存储单元中”）。 硬件：单片机为8K的98C52（ATMEL），LCD为北京青云的LCM141，标准串口总线为MAXIM的232芯片，时钟芯片为DS12887（DALLAS） -Function: the use of clock chip DS12887 in the LCD (LCM141) show time, through the 4 × 4 keyboard to modify the time and using the standard serial port to send MAXIM232. 4 × 4 keyboard in numeric keypad (0 ~ 9) and the function keys (F1 key for the

本文档包括单片机系统中常用到的时钟中断、通讯及键盘扫描等模块(见所附源程序)的说明。这些模块使用前后台系统模型。为达到最大的灵活性, 需要在用户工程中定义config.h文件, 在其中定义各模块可选参数的设置，而不是直接更改源代码。-this document, including SCM system clock used to the interruption communications and keyboard scanning modules (see accompanying source code) Note. These modules use before and after the Taiwan model. To achieve maximum flexibility in user defined config.h engineering documents, in the definition module optional parameter settings, and not to directly change the source code.