=== =时钟20:6=== === == 应先初始化状态寄存器 tx1714 EQU 7FFH PA EQU 05H PB EQU 0...

设计应用接口作为16位二进制编码器的输出口，并用该接口作为LED七段显示器的输出口,循环显示编码结果-Application Interface Design as a 16-bit binary encoder output, and the interface as a Seven-Segment LED display output cycle coding results show

可编程逻辑器件在数字式抢答器中的应用 -Programmable logic devices in digital Answer Explorer Application

LCD320240的AVR单片机驱动程序,显示的字模需行列式取模,液晶驱动芯片是1335-The AVR Singlechip LCD320240 driver, showed to be determinant of the matrix modulus, LCD Driver IC is 1335

STC单片机IO口模拟RS232测试程序,Keil Cx51应用开发技术中的程序主要的功能是在利用串口调试工具发送一个8bit的数据，而后单片机接收后把这个数据发送给模拟串口-STC Single-chip analog IO port RS232 test procedures, Keil Cx51 technology application development process is essentially the function is in the use of serial debug tools send an 8bit data, and then after the single-chip receive the data sent to the simulation of serial

ateml 8位AD通用程序-ateml 8 AD common procedures

本程序有友善之臂提供，为2440开发板的示例程序，请使用ADS编译。 简单使用说明： 使用H-Jtag或者更高级的仿真器调试，也可以不使用仿真器，借助supervivi的Download & Run功能测试， 下载的时候把DNW的下载地址设置为 0x30000000 即可。 本程序支持如下LCD: - NEC3.5"真彩LCD，分辨率240x320 - 7寸真彩LCD, 分辨率800x480 - VGA扩展模块,分辨率1024x768@70Hz 若要在LCD上正常显示CMOS摄像头，只需在Option.h文件中 改变LCD_TYPE的定义为相应的LCD即可。-This procedure has the arm of a friendly offer for the 2440 development board of the sample programs, use the ADS compiler. Simple instructions: Use H-Jtag or more advanced emulator debugging, you can not use the simulator, with the supervivi functional tests Download & Run, download time to download DNW address can be set to 0x30000000. This procedure supports the following LCD:- NEC3.5 " true color LCD, resolution 240x320- 7-inch true color LCD, resolution 800x480- VGA expansion modules, the resolution to 1024x768 @ 70Hz on the LCD display in the CMOS camera, only Option.h documents need to change the definition of LCD_TYPE corresponding to the LCD.

iic prog for mcu ok in keil c

当前LCM的主流接口有并口和串口。并口引脚多，产生串扰，串口则没有诸如此类的缺点。SPI作为串口家族的一员，具有高速同步、芯片管脚少和信号稳定不产生串扰等优点，越来越受到开发人员的青睐。但是，具有SPI的LCM并不是毫无缺点的，市场上以COG(chip on glass)方式封装的LCM大都是基于单工方式传输的，这将给开发带来了非常大的麻烦。本文主要论述基于单工SPI的GUI开发方案，详细地分析了基于单工SPI的GUI的开发开台，论述并分析在GUI开发过程中遇到的问题，最后提出增加虚拟LCD的方案解决这个问题。-err

ip2022 再线烧写软件 可以在线读写程序-ip2022 line again burning software can read and write online procedure

2003年全国大学生电子设计竞赛试题。设计分为5个模块：前轮PWM驱动电路、后轮PWM驱动电路、轨迹探测模块、障碍物探测模块、光源探测模块。有完整的设计实现及报告说明-2003 National Undergraduate Electronic Design Contest questions. Design is divided into five modules : front-wheel drive PWM circuit, rear-wheel drive PWM circuit, track detection module, module detect obstructions, light detection module. A complete design and realization report