好的学习资料arm7任何起步学好LIUNX下的AM7

uClinux上的应用程序设计对ARM芯片S3C44B0。-uClinux applications on the design of the ARM chip S3C44B0.

在BOOTLOADR中增加当今最好AES加密技术,可用于客户远程更新应用程式-BOOTLOADR increase in today

sdconfig.h: 该文件为SD卡读写模块配置头文件，用户可根据实际硬件条件进行修改. SD目录 : SD卡读写模块的全部文件,一般不用修改. 建议sdconfig.h文件不要放于SD目录中，因为SD目录中的文件一般无须修改,而sdconfig.h通常会有改动. -sdconfig.h: The document for the SD card reader module configuration header files, the user hardware according to actual conditions can be modified. SD directory: SD card reader module all the documents, the general need not be amended. sdconfig.h document recommends not to put in SD directory, because the SD files in the directory are not normally required to be amended and the changes are usually sdconfig.h.

开发环境:ADS 1.2/SDT 2.51 GUI测试，由于没有触摸屏，所以将触摸屏的代码给屏蔽了； 请将FS44B0II开发板连接好交叉网线、直连串口线、电源， 并连接好G57液晶屏，同时还要连接好背光电源； 然后在BIOS的命令窗口里面敲netrun命令； 点击FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel目录下： 批处理文件FS44B0_G57_uCGUI.BAT 下面你就可以看到液晶屏上面显示优龙标志 它会延时一两秒中进入下一个画面，逐步延时GUI的各项功能，请耐心观看； -Development Environment: ADS 1.2/SDT 2.51GUI test, because there is no touch screen, it will be touch screen to shield the code Please FS44B0II development board to connect a good cross-network lines, direct serial lines, power supply, and connect a good G57 LCD screen, at the same time, good backlight power supply connection and then in the BIOS command window knock netrun order Click FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel directory: batch file FS44B0_G57_uCGUI.BAT below you can see the LCD screen above shows excellent signs that it will delay Liuzhou 1 two seconds to enter the next screen, and gradually delay the GUI features, please be patient watch

注意:本文件并未压缩,仅为你需要,加上后缀. 超猛 ARM CPU上的GCC环境-Note : This document has not been compressed, you need only, with the suffix. Bets on the ARM CPU GCC environment

在ＡＲＭ２４１０支持汇编指令集，可在Ｓ３Ｃ２４１０上运行．-ARM2410 support in the compilation instructions, the S3C2410 running.

c8051一个EMIF控制的例子，课业可以看看！-C8051 a EMIF control example, tasks can have a look at!

最近完成的LINUX下RTC8025的驱动，平台：AT91RM9200，主要实现时钟操作的几个接口，对开发同类产品的驱动很有借鉴作用。-recently completed RTC8025 LINUX driven platforms : AT91RM9200. main clock operation of several interfaces, the development of similar products in a very useful reference drive.

一个很好的可以用来调试51单片机的串口程序。-a good 51 can be used to debug the MCU Serial procedures.

资源描述            k60dn512的示例程序。有着比较完备的驱动示例程序，K60的外设驱动几乎都有。