多功能遥控小车的软硬件设计程序，包括使小车前进、后退、左转弯、右转弯、左滚动、右滚动的基本指令，以及完整程序清单。...

开发环境ADS， 直流电机控制实验 掌握使用PWM方式控制直流电机的转动速度。-Development Environment ADS, DC motor control experiment to master the use of PWM control of DC motor rotation speed.

让您通过VB介面，简易地测试8051上面的40Hz的RF通讯。

用C8051F040实现DA（模拟-数字）变换。C8051F040集成了12位精度的DA转换器。-With the C8051F040 to achieve DA (analog- digital) conversion. C8051F040 integrates a 12-bit accuracy of the DA converter.

PIC单片机程序设计基础 入门教程.-PIC Design Basics Guide.

飞利浦RC522芯片源代码。该芯片主要针对三表市场和手持设备，支持I2C/SPI/UART接口。 先发布基于普通51单片机的驱动源代码，采用串口接口，无需中断。只要接一个串口，后续会发布基于飞利浦LPC9401的读写源代码！LPC9401也是基于51核，只需连接SPI接口！有公司拿这个源代码卖钱哟-Philips RC522 chip source. The chip targeted at three tables and handheld devices market, support I2C/SPI/UART interface. Based on the first general release 51 MCU-driven source code, using serial interface, without interruption. As long as a serial port access, the follow-up will be issued based on the Philips LPC9401 write source code! LPC9401 is based on the 51 nuclear, only connecting SPI interface! A company with the source code acquisition yo! !

最近作的AD9852的FM扫频模式，自动计算频率，采用单片机的总线访问方式，非常方便，你要做 的就是填数-Recently, the AD9852 for the FM sweep mode, automatic calculation of the frequency of the use of single-chip bus access method, a very convenient, you have to do is fill in a few

STK500_2下载器 M8 支持bootloader(带bootloader源码) 使用STK500_2 协议的ISP下载器，监控芯片 M8,数据通讯RS232.使用 ATMEL AVRStudio 4.xx STK500工具的进行软件升级。可通过ATMEL AVRStudio 4.xx STK500工具升级固件程序。升级方法：通过设定电压 即按“write voltage”按钮进入bootloader程序。 -M8 browser support STK500_2 download bootloader (with bootloader source code) to use the ISP to download STK500_2 agreements, and monitor chip M8, data communication RS232. Use ATMEL AVRStudio 4.xx STK500 tool for software upgrades. By ATMEL AVRStudio 4.xx STK500 firmware upgrade tool. Upgrade methods: by setting the voltage that is, according to

ATmega16L控制IDE硬盘的源代码,可以读写扇区,无文件系统-IDE hard disk source code, can read and write Sector, no file system

CAN的调试程序。CAN的初始化重要包括下面几个方面。RXB0SIDH，RXB0SIDL，RXB0MIDH，RXB0MIDL。这是接收过滤器。TXB0SIDH，TXB0SIDL，TXB0DLC，这是发送标志位。还有波特率寄存器。操作模式为 正常模式。-CAN debugging procedures. CAN initialization important aspects include the following. RXB0SIDH, RXB0SIDL, RXB0MIDH, RXB0MIDL. This is the receiver filters. TXB0SIDH, TXB0SIDL, TXB0DLC, it is sending signs spaces. There baud rate register. The normal mode of operation for the model.

液晶显示器12864的805X接口程序,汉字点阵显示-the 805X interface program, Chinese characters dot matrix display