图基本专业开发套件

c8051f020 的扩展8255驱动数码管显示 同样是keilc啊-C8051F020-driven expansion of 8255 is a digital tube display the same keilc ah

亮灯控制程序,按下某键即执行相应程序,没按其他键,状态不变-lighting control procedures, press a button that is the implementation of the corresponding procedures, not by the other key, the status quo

凌阳最出的超声波测距模组，通过555产生40KHz的超声波，有SPE061A单片机控制超声波的发射和接收，最初的版本在程序方面比第二版本来得简单，主要是通过了硬件电路减少了程序，附电路图、PCB图等-Sunplus most of the ultrasonic ranging modules, 40KHz generated through 555 of the ultrasound, ultrasound has SPE061A single-chip microcomputer to control the transmitting and receiving an initial version of the procedure than the second version is more simple, mainly through the reduction of hardware circuit procedures, with schematics, PCB map

单片机系统上电后，P0 口和 P1 口都被清 0。然后，你规定一个由 6 个数字构成的序列（每个数字从 0～F 中选取），比如 E、8、9、0、7、F。然后每次当单片机检测到外部中断 0发起中断时间时，读取 P0 口和 P1 口上的状态值，当连续 6 次外部中断事件的对应的数字序列构成你所设定的序列后（举例来说，如果 P0.0 是 1，P0 和 P1 的其他管脚是 0，那么我们称为检测到一次数字 0），从串口打印输出一幅类似下图的 16×16 的ASCII码的圣诞树图片。-Single-chip microcomputer system after power, P0 and P1 mouth I have been ching 0. Then you set a six figure constituted by the sequence (each number from 0 ~ F in selected), for example, E, 8,9,0,7, F. And then each time a single-chip detects external interrupt 0 initiated interruption time, I read the P0 and P1 mouth on the state value, when a row 6 times the corresponding external interrupt events constitute digital sequence set your sequence (for example example, if P0.0 is 1, P0 and P1 of the other pin is 0, then we called a number of detected 0), a printout from the serial port under similar 16 × 16 map of the ASCII code of the Christmas tree图片.

单片机 AT89C52 的中文资料 适合新手 学习！重要基础单片机资料-SCM AT89C52" s Chinese data suitable for novice to learn! An important foundation for SCM information

红外遥控接收 ORG 0000H LJMP START 转入主程序 ORG 0010H START: MAIN: JNB P2.2,IR LJMP MAIN 以下为进入P3.2脚外部中断子程序，也就是解码程序 IR: MOV R6,#9 SB: ACALL DELAY882 调用882微秒延时子程序 JB P2.2,EXIT 延时882微秒后判断P3.2脚是否出现高电平如果有就退出解码程序 DJNZ R6, SB 重复10次，目的是检测在8820微秒内如果出现高电-infrared remote control receiver ORG 0000H LJMP START into main program ORG 0010H START : MAIN : JNB P2.2, IR LJMP MAIN below to enter P3.2 foot external interrupt subroutine, which is decoding procedures IR : MOV R6, SB# 9 : Calling ACALL DELAY882 882 microsecond delay subroutine JB P2.2, EXIT 882 microsecond delay after the judgment whether there P3.2 feet to I quit if decoding procedures DJNZ R6, SB repeated 10 times, the purpose is to test if within 8,820 microsecond high

一个完整的个人产品开发源代码,包括对单片机STC12C5410的编程(含内部AD采样、自创的内部Flash编程源码等)、LCD1602的驱动编程等。-A complete source code of the individual product development, including single-chip STC12C5410 programming (including the internal AD sampling, create their own internal Flash programming source code, etc.), LCD1602 driver programming.

利用C语言进行24lc256与单片机的通讯程序-The use of C language SCM 24lc256 and communication procedures

485单相电能表开发程序，液晶显示。采用AD7755设计，可与掌上电脑连机通信设置各种电能表参数。-485 single-phase energy meter development process, liquid crystal display. Design using AD7755 can be connected Pocket PC communication settings of various parameters of energy meter.

多任务操作系统ucOSII移植到Keil上的源码-Multi-tasking operating system ucOSII transplanted to the source Keil