tms320c5409 dtmf source code

ipp打印机服务器原代码 注意：请将ipp.gz改为ipp.tar.gz 然后使用tar zxvf ipp.tar.gz解压 站长注意，为何不能上载tar.gz后缀的文件给用户造成不变！-ipp printer server to the original code : I would be grateful if ipp.gz ipp.tar.gz then use to tar zxvf ipp.tar.g z decompression station attention, why not on the tar.gz extension of the document to users unchanged!

介绍一种基于红外光电传感器的智能车自动控制器设计方案。以飞思卡尔16 位单片机为核心控制单元，使用红外光电传感器采集路径信息，控制智能车的舵机、驱动电机，实现智能车的自主寻迹行驶。-Introduction of a photoelectric sensor based on infrared automatic controller for intelligent vehicle design. Based on Freescale 16-bit microcontroller as the core control unit, the use of infrared photoelectric sensor acquisition path information, control, intelligent vehicle steering gear, drive motors, autonomous intelligent vehicles driving tracing.

本程序为最小二乘法，已经在kei　上运行过，非常适应与pid的运算中-procedures for the least-squares method, in kei run-off, very Adaptation and the pid Operation

DS1307 实时时钟

静态驱动也称直流驱动。静态驱动是指每个数码管的每一个段码都由一个单片机的I/O端口进行驱动，或者使用如BCD码二-十进制译码器译码进行驱动。静态驱动的优点是编程简单，显示亮度高，缺点是占用I/O端口多基于89c52的数码管静态显示

realview下的一个arm9的bootloader烧录器.支持norflash读写-RealView ARM9 under a burner of the bootloader. norflash read and write support

PIC单片机做的逆变器，有原理图和整套源代码！适合新手参考，也适合一些工程师直接使用，有详细的功能说明文件。可以下载下来看一下！很有用的，如果有不明白的可以联系我。

c语言写的用于单片机mps430的底层通信协议，包含了bch编解码，交织编解码，和crc校验。经过简单的修改即可用于其他的单片机。-write for the MCU mps430 underlying communication protocol includes the BCH encoding and decoding, codecs are intertwined, and crc check. After a simple modifications can be used in other SCM.

ISP for STR73X 默认情况下, bank0 是映射到地址0x00. 考虑到,IAP程序需存储在bank1,而用户程序需存储在bank0. 因此须使用CAPS工具,将bank1映射到地址0x00. 另外, 在IAP程序运行期间,必须在执行用户程序跳转之前,通过程序将bank0重映射到地址0x00(注:IAP程序已经实现了bank0重映射到地址0x00,用户不需要自己来编写代码).-ISP for STR73X default, bank0 is mapped to address 0x00. Taking into account, IAP process is stored in the bank1, while the user program to be stored in bank0. It is necessary to use the CAPS tool bank1 mapped to address 0x00. In addition, IAP procedure during operation must be in the implementation of user program before Jump through the procedure will bank0 re-mapped to address 0x00 (Note: IAP program has achieved bank0 re-mapped to address 0x00, the user does not need to write their own code).

U-Boot1.1.2是最为常用的嵌入式系统Bootloader，这个版本是目前的最新版本-U-Boot1.1.2 is the most commonly used in embedded system Bootloader, this version is the latest version