一款收款机C源代码！因为是几年前的代码了，比较经典，还是共享一下！ 里面有不少算法还是很不错的，注意用三菱16位30802的编译器...

波形发生器的源程序，能产生方波、三角波、和矩形波三种波形-The source waveform generator, which can produce square, triangle wave, and rectangular-wave three kinds of waveforms

cs5463的pic初始化程序,对cs5463进行初始化，用于与pic单片机通讯。-CS5463

本设计以P89V51RD2FN单片机为电动小车的控制核心，采用MSA-LD2.0倾角传感器实时测量跷跷板的倾斜角，用ST198光电传感器检测黑色引导线监测小车运动。光电传感器和倾角传感器模块把实时测量信号馈送至单片机，利用专用细分芯片TA8435H驱动步进电机，以脉宽调制式斩波方式对步进电机步进角进行细分，控制和调节小车速度。采用增量式PID控制算法确保小车能够达到平衡；用RT128×64M液晶显示时间、角度等参数。经测试表明：小车各项性能指标达到设计要求，能够实现30秒内小车行驶到规定点，并保持跷跷板平衡；在跷跷板一端配重可调整的情况下，小车也能自动找到平衡点并保持跷跷板平衡。-The single-chip design for the electric car P89V51RD2FN control of the core, the MSA-LD2.0 seesaw angle sensor real-time measurement of the tilt angle, the detection of black ST198 photoelectric sensor to monitor vehicle movement and guide lines.Photoelectric sensors and angle sensors in real-time measurement module to feed the signal to the microcontroller, using a dedicated sub-chip stepper motor driver TA8435H to PWM chopper-type stepper motor on the sub-stepping angle, control and regulation vehicle speed. The use of incremental PID control algorithm to ensure that the car can achieve balance with LCD RT128 × 64M time, angle and other parameters.After the test showed that: the performance car

MSP430基本编程学习资料 （端口，时钟，定时器，。。。）-Basic learning materials MSP430 Programming

基于AT89C2051单片机的数字电容表设计。里面有源代码、protues仿真图-AT89C2051 MCU-based design of digital capacitance. Inside the source code, protues simulation map

keil C51 Switch事例-examples Switch

报警程序，本程序可以用于测试设备运行过程中的报警信息，用于和用户之间进行交流。-Police procedures, the procedures can be used to test equipment during the operation of the alarm information, and users for the exchange between.

CDLEA.hex CDLEA_Main.c CDLEA.hex为已编译的红外遥控音源切换器的单片机程序 CDLEA_Main.c为源代码 CDLEB.hex CDLEB_Main.c CDLEB.hex为已编译的加强版的红外遥控音源切换器的单片机程序 　　有红外遥控PC功能,PC软件可使用Grider3.2(SAA3010T电视遥控器) 　　Grider3.2可到http://cdle.yeah.net下载 CDLE_A410.exe 为红外遥控音源切换器的ＰＣ应用软件。-CDLEA.hex CDLEA_Main.c CDLEA.hex compiled for the red outside sources of remote switching of SCM CDLEA_Main.c procedures for the C source code CDLEB.hex DLEB_Main.c CDLEB.hex compiled for the enhanced version of the infrared remote control sources of the single switches machine procedures with infrared remote control PC functions, PC software can be used Grider3.2 (SAA3010T TV remote control) Grider3 .2 can http :// cdle.yeah.net download CDLE_A410.exe sources of infrared remote control switches the PC application software.

51单片机控制TC35I无线通信模块的完整Keil C程序，还包含GB2312与Unicode转换，国标汉字、ASC字符显示，串口通信，液晶模块控制等程序。-51 single-chip wireless communication module TC35i control the integrity of Keil C procedures, also includes GB2312 and Unicode conversion, GB characters, ASC characters display, serial communications, LCD module control procedures.

这是由C51单片机实现的接触式IC卡的读写-This is achieved by the C51 single-chip contactless IC card read-write