Agilent 86100C GPIB & GPIB card programming 文件

mscomm控件控制多串口-mscomm control over Serial Control

通用串口通信C程序实现源码.带有已经在windows下编译好的dll动态库-Universal Serial Communication C program to achieve source code. With the already compiled dll in the windows under the dynamic library

串行数据标准选用之我见 RS-232、RS-422与RS-485标准及应用 转换器的构成 -Selection of serial data standards, I see the RS-232, RS-422 and RS-485 standards and the application of the composition of converter

3.CB_seri.cpp(C++Builder串行异步通信程序)-3.CB_seri.cpp (C Builder asynchronous serial communication program)

将串口通讯协议存储为一个通讯文件，可是随时将存储通讯协议文件调入计算机运行与下位机通讯可以实现通讯对话，-Serial communication protocol will be stored as a communications document, but to keep the communication protocol storage document transferred to the computer is running and the next-bit machine communication can realize communication dialogue

这是用KeilC做的nRF9E5发射程序,可以用的,是做射频的好代码.-This is done using the nRF9E5 KeilC launch procedures can be used to be so good RF code.

用vb实现串口间通信,可以用来熟悉串口间传输信息的原理.-with Serial Communication, which can be used with serial transmission of information between the principle.

Verilog实现的UART程序，用ISE打开工程文件即可-Verilog implementation UART program, open the project file with the ISE can be

本程序是针对特定GPS接收机--JAVAD公司的legacy的一个应用，用来收取标准的NMEA-1083GGA信息或JPS格式（JAVAD公司的特有GPS信息格式）的{RT，PO}信息，并统计数据大小与经历时间。本程序用VC6.0+串口控件MSComm实现，其中关于如何在数据长度不定的情况下实现数据帧的同步的方法可以借鉴到其它串口数据采集的应用之中，具备一定的实用价值-this program is targeted at specific GPS receiver-- JAVAD the legacy of an application, used to collect standard NMEA- 1083GGA information or JPS format (JAVAD company"s unique GPS information format) (RT, PO) information and statistical data on the size and duration. The procedures used VC6.0 Serial MSComm control, on how volatile the data length of the data frame synchronization method can draw on to other serial data acquisition applications, to have some practical value

本程序是i2c总线读写一个字节的程序。在写过程序中，不一定非要检测i2c的应答位，可以直接延时过去就行，但是在读过程中必须给应答信号，读完发停止位，一定确认所发的信号都发上了。否则在连续地址读的过程中可能不会出错，但是在随机度过程中就会出错，我的程序就是在给停止信号时没有给上，24cxx一直在输出数据，结果读出错。找着问题后我的程序只加入了一条命令便完全正常。-i2c bus read and write a byte procedures. The written procedure, not necessarily require the detection i2c-response, and can directly past trip delay, but the process must be read to the response signal, stopped at reading, we recognize the signals are on the fat. Otherwise, the address read for the course could not go wrong, but the randomness of the process would be a mistake, I was in the process to stop for no signal, 24cxx in output data, read errors. I discovered the problem after the procedure just joined the order of a completely normal.