m25p64是AT退出的一款大容量flash存储器，8Mbyte.串行通信方式，极大的节省了硬件资源。...

这个是用MedWin配合proteus仿真的单片机程序，使用的AT89S52单片机控制14个数码管动态扫描，实现时钟和日期显示。并有按键控制，仿真也通过，内部附有HEX文件-This is MedWin microcontroller simulation with Proteus, the use of the AT89S52 Singlechip control 14 digital control of dynamic scanning, the realization of the clock and date display. And a button control, through simulation, the internal file with HEX

对于基本的显示屏1602,怎样用最简单的方式操作呢,本程序就给了一个实例.-1602 for the basic screen, how to use the most simple way to operate it, the program gives an example.

C8051F020的KEIL工程文件，包括一些内部资源使用代码，以及TS19264的驱动程序-C8051F020 KEIL project, including some internal resources to use code, as well as TS19264 drivers

单片机实验，实现双字节无符号数的加法，利用查表指令，在此基础上可以学习查表指令的用法-SCM experiment, to achieve double-byte unsigned number of addition, using look-up table instructions, on this basis, can learn the usage of table look-up instruction

可以直接将图片转化为lcd 的源代码，很方便你的使用。-Can be directly translated into lcd picture of the source code, very easy to use you.

单片机播放音乐 通过控制高低电平让蜂鸣器发出不同的声音 做相应的延时实现节拍 开发环境是keil-SCM music by controlling the high-low so that the buzzer sounds different delay accordingly to achieve the beat

51单片机串口数据包收发程序，能一次收发多个字节，可跟据需要自行修改字节长度，并且具有接收超时判断功能。-51 Single-chip serial data packets to send and receive procedures, can send and receive more than one byte can be modified according to the needs of self-byte length, and have to receive overtime to determine function.

DK3200开发板上的ADC开发出的AD和PWM应用程序，可以在LED上显示测量结果-DK3200 Development Board of the ADC developed AD and PWM applications, can be displayed on LED measurement results

6段数码管分别显示，时，分，秒，四个按键，K1（P0.0），K2（P0.1）， K3（P0.2），K4（P0.3），四个按键用来调时间的，按下K1，所有位都清零显示，然后按下K2，秒在闪烁，继续按K2分闪烁，不段地按K2 秒--分--时切换着闪烁，在某位闪时按下K3相应位加一，确认调整，按K4，取消调整再按K1。在K1按下以后才有调时的功能，如果K1没有按下，按别的键没有反映。这为了在加点按键功能留着用 -6 respectively of the digital control, when, minutes and seconds, four keys, K1 (P0.0). K2 (P0.1), K3 (P0.2), K4 (width), the four keys to the transfer time, press the K1, All spaces are reset, then press K2, the scintillation seconds, according to K2 pm flickered. not according to K2 of seconds-- minutes-- when switching to flicker in certain press the flash-K3 corresponding increase in a confirmed adjustment by K4, then canceled K1 adjustment. K1 in the press will only be made after the transfer of function, if K1 pressed by other key is not reflected. This points to the function keys used Retention

使用C8051F020和FPGA等其它相关硬件制作的一个程控滤波器，里面包括详细的源代码和设计文档，希望对大家有用。-C8051F020 and FPGA use and other related hardware produced by a program-controlled filter, which include detailed source code and design documents, in the hope that useful to everyone.