ht16512是变频器（真空荧光显示屏）控制设备直接对应…

一个不错的硬盘播放器程序,包含VFD显示程序,红外线遥控程序,硬盘读写程序,及解码程序等.-a good hard disk player procedures, including procedures VFD, infrared remote control procedures, hard drive read and write procedures and decoding procedures.

51单片机制作的电子钟，增加日期显示，带有详细的注释。-51 MCU production of electronic bell, the date of increase, with detailed comments.

T6963液晶程序，直接可用５１单片机控制-T6963 LCD process, directly available to 51 single-chip control

设计使得原本需要14个IO接口的键盘显示少用了9个单片机IO接口,虽然该设计的优势在本实验中没有完全体现出来,但若在现代工业设计中应用此方案,在对引脚需要较大的产品中其优点将体现得淋漓尽致。.-Design makes the original needs 14 IO interface shows the use of a keyboard 9 Singlechip IO interface, although the advantages of the design in this experiment did not fully reflected, but in modern industrial design in the application of this program in the pairs of primers Products feet larger in its merits and will be reflected most vividly. .

请将下载的2个插件内容拷贝到uVision 的安装目录下的 KeilC51BIN 中 2. 修改 Tool.ini, 此文件位于 uVision 的安装目录 keil 下. 请将下面的内容 添加到 [C51] 部分的后面. AGSI1=ledkey.dll ("ledkey") AGSI2=simboard.dll ("simboard") 3. 重启uVsion. 进入Debug 模式, 打开菜单Peripheral, 发现增加了2项 分别是键盘LED仿真板，51实验仿真板。-Please download the contents of two plug-ins are copied to the installation directory uVision under KeilC51BIN 2. Modify Tool.ini, this file is located in the installation directory uVision under keil. Please Add the following line to [C51] part of the back. AGSI1 = ledkey.dll (ledkey) AGSI2 = simboard.dll (simboard) 3. Reset uVsion. entered the Debug mode, open the menu Peripheral, found an increase of 2 are keyboard LED emulation board, emulation board 51 experiments.

介绍了液晶显示模块基本原理及其技术特性，与单片机的进行接口的具体电路，同时给出了其编程方法和程序代码．-Introduced the basic principles of liquid crystal display module and its technical characteristics, and MCU interface to the specific circuit, at the same time gives the methods and procedures of its programming code.

这篇实验报告是关于单片机多路数据采集的，本实验由2大部分组成：1、为用EPOROM构成的心电信号发生器；2、为多路信号的微机采集与显示；第一部分实验主要研究可编程序存储器EPROM的非计算机应用。把存储在EPROM中的数字心电信号读出并通过D/A转换为模拟信号显示在示波器屏幕上。 第二部分实验的目的是研究一个数据采集系统，该系统利用ECD-51型单片机为中心，由D/A芯片等将各种低频信号以及由EPROM产生的模拟人体心电信号变换成离散的数字信号存入微机内存，以待进行数据处理和分析，然后再通过D/A转换将其还原成模拟信号显示在示波器的屏幕上。 -This experimental report on the multi-SCM data acquisition, the experiment by the two major components : 1. EPOROM pose for the use of the ECG signal generator; 2, multi-path signals in the computer acquisition and display; the first major study of experimental programmable EPROM memory in non-computer applications. Stored in the EPROM of ECG read out by D/A conversion of analog signals displayed on the oscilloscope screen on. Part II The purpose of this experiment is to study a data acquisition system, which uses ECD-51 microprocessor as the center, from the D/A chips, and other various low-frequency signal from EPROM and the simulation of human ECG transform into several discrete signal words into computer mem

闪光灯测试仪的程序代码，有基于proteus的仿真-Flash tester code, there are simulation-based proteus

51io模拟串口程序-51io simulation procedures

可以实现fat文件系统，在单片机上也可以进行改造！-can achieve fat file system, the MCU can also transform!