ollydbg脱壳脚本，可脱asppack壳

设计一种自动洗衣机的程序控制器，在启动后先进水，等到达高水位后，启动洗衣马达转动4min，如在洗衣过程中发现水位低于高水位，则停止洗衣马达转动并报警，并在水位到达高水位后再次启动马达。洗衣结束后则启动排水开关，待水位到达低水位后，则启动脱水马达，转动2min。如此重复三次，要求在每一动作之间有2s的间隔。 高水位，低水位为水位传感器，用两个开关模拟，当水位高于高水位或低于低水位时，两个开关的状态分别为0 。启动开关用一个开关表示。进水、排水、洗衣马达、脱水马达及报警分别用一个发光二极管表示。本实验只需用可编程并行接口电路的A口。其硬件接口如下图所示。也可采用可编程逻辑器件进行设计。 -Design of an automatic washing process controller, after commencement of advanced water, and so on to reach the high water mark, start laundry motor rotation 4min, such as in laundry water level lower than that found during the high water mark, then the motor stops rotating laundry and alarm, and the the water level reaches the high water mark again to start the motor. Laundry is started after the end of the drainage switch, when the water level reaches the low water level, then start the dehydration motors, rotating 2min. Repeat three times, each action requires the interval between the 2s. High water, low water level as water level sensors, with two analog switches, when the water

汇编程序案例6数据加密程序encode.rar-Assembler Case 6 data encryption procedures encode.rar

8*8 LED 点阵屏幕显示全屏下滚2次及上滚2次,从左到右,从右到左各收缩1次.从中间扩展到四角,从四角收缩到中心,然后再显示:"祖国您好 合肥市 邦森公司 国庆" 作为LED点阵练习,简单易懂.-8* 8 LED dot-matrix display full-screen under the roll-on roll 2 times and 2 times, from left to right, from right to left each contraction 1. From the middle extended to the four corners, from the contraction to the center square, and then displays: " Fatherland Hello, Hefei, Bunsen" s National Day" as a LED dot matrix exercise, easy to understand.

出租车计价器的汇编源程序 比较周全的考虑了实际中所会碰到的问题-the taxi program

asfsfdsvsdvasvsdvdvdvssdvdvsdasdasdasdasdasdasd

回溯法实现最小圆排列问题-Backtracking minimize problems with a round

几个汇编小程序 例如字符传换,显示字符串 爱好学汇编者下载一用-compilation of several small programs- for example, for characters, the string-loving study showed compilers with a download

用matlab所编用传输矩阵法计算光子晶体的能带结构的程序-prepared by using Matlab using the transfer matrix method photonic crystals with the structure of procedures

这是LCD液晶显示器的主要控制器hd61830的软件包，希望能给大家带来帮助。-This is the LCD display controller hd61830 the main package, in hopes of giving us some help.

电动车从起跑线出发（车体不得超过起跑线），沿引导线到达B点。在“直道区”铺设的白纸下沿引导线埋有1~3块宽度为15cm、长度不等的薄铁片。电动车检测到薄铁片时需立即发出声光指示信息，并实时存储、显示在“直道区”检测到的薄铁片数目。 （2）电动车到达B点以后进入“弯道区”，沿圆弧引导线到达C点（也可脱离圆弧引导线到达C点）。C点下埋有边长为15cm的正方形薄铁片，要求电动车到达C点检测到薄铁片后在C点处停车5秒，停车期间发出断续的声光信息。 （3）电动车在光源的引导下，通过障碍区进入停车区并到达车库。电动车必须在两个障碍物之间通过且不得与其接触。 （4）电动车完成上述任务后应立即停车，但全程行驶时间不能大于90秒，行驶时间达到90秒时必须立即自动停车。 -err