液晶1602C51程序，P1口做数据线P2口做控制线

VB与S7200的PPI通信-VB and the PPI communications S7200

用单片机I/O口模拟总线形式的通用驱动程序，用C51编写-MCU I/O simulation generic form of bus drivers, prepared with C51

chm格式的pic单片机原理 和适合新人阅读参考-chm format, suitable for new pic microcontroller theory and reading the reference

用C语言写的红外遥控解码程序，，，， 语法上没错，但解码完成后有错，，没个按键的都一样，，不知道什么问题，望指点，，EMAIL:wjsjdeng@sina.com.cn-C language to write the infrared remote control decoder,, the grammar is correct, but after the completion of decoding wrong, not a button are the same, and do not know what, look a spot, EMAIL : wjsjdeng@sina.com.cn

端口控制发光二极管亮灭。 【硬件连接】通过SPCE061A的1位I/O端口（本例中使用IOA15端口），经一限流电阻后接一个发光二极管至地-Port control to eliminate bright light-emitting diodes. [] Through SPCE061A hardware connection of an I/O port (in this example, the use of IOA15 port), with a current limiting resistor followed by a light-emitting diodes to land

单片机的c语言的编译软件，最新的keil 2英文版。-keil 3

简单的单片机LED，用串口调试来实现其LED的显示。数码管的显示-Simple single-chip LED, using serial debugging to achieve its LED display. Digital tube display

密码锁的设计,单片机初学者必须程序,适用于proteus-Locks design, single-chip microcomputer program for beginners to be applicable to proteus

三相步进电机的三相六拍工作方式，正转的绕组通电顺序：A、AB、B、BC、C、CA、A，反转的通电顺序：A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性，故步进电机的工作过程中不能及时的启动和停止，在启动时应慢慢的加速到预定速度，在停止前应逐渐减速到停止，否则，将产生失步现象。 步进电机的控制问题可总结为两点： 1、产生工作方式需要的时序脉冲； 2、控制步进电机的速度，使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.

msp430系列介绍 msp430系列介绍 msp430系列介绍-msp430系列介绍msp430系列介绍msp430系列介绍msp430系列介绍