-
ucos_iiUCOS_TE2410开发板源码.rar
UCUCOS_TE2410开发板源码.rar
- 2022-11-05 21:05:04下载
- 积分:1
-
MMA7455 with 430 single
用430单片机测试MMA7455三维加速度传感器程序。-MMA7455 with 430 single-chip three-dimensional acceleration sensor program.
- 2022-03-16 22:47:52下载
- 积分:1
-
代码说明了一个ps2口驱动和编程方法。主要是鼠标,当鼠标产生中断时,主板上的蜂鸣器和运行灯都有反映。移动鼠标或点击鼠标的左右键,发现主板有反映。注意,因为程序并...
代码说明了一个ps2口驱动和编程方法。主要是鼠标,当鼠标产生中断时,主板上的蜂鸣器和运行灯都有反映。移动鼠标或点击鼠标的左右键,发现主板有反映。注意,因为程序并没有驱动滚轮,所以鼠标滚轮不能产生中断。--PS2 port driver and programming method. When mouse generates an interruption, alarm and light will have response. You could move mouse or hit the left or right button, and observe the reaction of motherboard.
- 2022-02-09 21:46:16下载
- 积分:1
-
tms320vc5509a usb boot
tms320vc5509a usb boot -tms320vc5509a usb boot
- 2022-03-22 03:30:40下载
- 积分:1
-
IIC总线,I2C,用于LPC21XX系列的,LPC2103。用非中断的方式写的,直接用IO口控制。非常好用。...
IIC总线,I2C,用于LPC21XX系列的,LPC2103。用非中断的方式写的,直接用IO口控制。非常好用。-IIC Bus, I2C, for LPC21XX series, LPC2103. With non-disruptive way to write and direct use of IO population control. Very easy to use.
- 2022-05-13 09:12:42下载
- 积分:1
-
keil MDK开发环境,实现STM32的USB驱动程序,实现USB端的DEVICE功能,内附驱动源码,欢迎交流,...
keil MDK开发环境,实现STM32的USB驱动程序,实现USB端的DEVICE功能,内附驱动源码,欢迎交流,-keil MDK development environment to achieve STM32" s USB driver, USB side to achieve DEVICE function, enclosed driver source code, welcome exchanges,
- 2023-01-14 02:10:03下载
- 积分:1
-
24C02读写源程序,测试OK!
24C02读写源程序,测试OK!--24C02 read/write operation.
- 2022-02-18 15:18:49下载
- 积分:1
-
DS1302编程学习用时钟芯片片 DS1302编程学习用时钟芯
DS1302编程学习用时钟芯片片 DS1302编程学习用时钟芯-SGDGDGDFGHHFHGKJHKJHLJKLJK;LKL;KL
- 2022-01-21 23:16:57下载
- 积分:1
-
钳入式开发的operation system
是追简单的example
钳入式开发的operation system
是追简单的example...
钳入式开发的operation system
是追简单的example
钳入式开发的operation system
是追简单的example-clamp-in the development of the recovery operation system is a simple example of the clamp-in development of the operation system is a simple example to recover
- 2023-05-29 01:30:03下载
- 积分:1
-
AT91RM9200的USB host和USB device的代码ADS1.2.
USB
AT91RM9200的USB host和USB device的代码ADS1.2.
USB-Device测试程序:
因为程序运行在SDRAM中,所以要先初始化SDRAM(可用basic boot程序初始,之后不能复位或断电),再运行此程序,程序运行后连接USB端口,计算机会提示检测到新硬件,安装硬件驱动程序atmusb6119.inf
后计算机会把USB端口虚拟为一个串行的端口使用-AT91RM9200 the USB host and USB device code ADS1.2.USB-Device test procedure: Because the procedure is running in SDRAM, and so we have to initialize SDRAM (available for the initial basic boot procedure, followed by Can not reset or power off), then Run this program, the program to run after connecting USB port, the computer will be prompted to detect the new hardware, installing hardware drivers after the computer will atmusb6119.inf virtual USB port to a serial port to use
- 2022-01-30 16:36:24下载
- 积分:1