ASP的web在线聊天室源码，程序实现了许许多多的特点…

This file were downloaded from the Programmers Heaven CD-Rom. More information about this CD-Rom can be found at the following WWW pages: http://www.algonet.se/~synchron http://www.infomagic.com synchron@algonet.se orders@infomagic.com-This file were downloaded from the Program mers Heaven CD-Rom. More information about stories "s CD-Rom can be found at the following Web pages : http://www.algonet.se/ ~ synchron http :// or www.infomagic.com synchron@algonet.se ders@infomagic.com

中断列表(4) 712K-suspended list (4) 712K

资源描述EV1527解码程序:单片机PIC16F630,内部4MHz,EV1527发射频率433MHz,振荡电阻270K,遥控器供电电压DC12V,周期为1.2ms。 在上电3S钟内按开机键，程序学习遥控器识别码，1次只能学习一个遥控器；按关机键程序将擦除所有遥控器识别码。 本程序最多可以学习42个遥控器，当遥控器个数满42个后第43个将会覆盖第1个。

E2PROM c51程序，已经在我的平台上调试通过了，芯片可以是各大厂家的24C0x系列产品。-E2PROM c51 procedures, has been in my debug platform adopted, the chip can be 24C0x major manufacturers products.

本程序是基于51单片机的红外解码实验！！希望大家喜欢-This procedure is based on 51 single-chip decoder infrared experiment! ! I hope everyone likes

一个rs-232接口的程序，已经通过调试。收发只用一个定时器。主芯片――8xC751-an rs-232 interface procedures have been adopted debugging. Transceivers only a timer. Main chip-- 8xC751

设计一种自动洗衣机的程序控制器，在启动后先进水，等到达高水位后，启动洗衣马达转动4min，如在洗衣过程中发现水位低于高水位，则停止洗衣马达转动并报警，并在水位到达高水位后再次启动马达。洗衣结束后则启动排水开关，待水位到达低水位后，则启动脱水马达，转动2min。如此重复三次，要求在每一动作之间有2s的间隔。 高水位，低水位为水位传感器，用两个开关模拟，当水位高于高水位或低于低水位时，两个开关的状态分别为0 。启动开关用一个开关表示。进水、排水、洗衣马达、脱水马达及报警分别用一个发光二极管表示。本实验只需用可编程并行接口电路的A口。其硬件接口如下图所示。也可采用可编程逻辑器件进行设计。 -Design of an automatic washing process controller, after commencement of advanced water, and so on to reach the high water mark, start laundry motor rotation 4min, such as in laundry water level lower than that found during the high water mark, then the motor stops rotating laundry and alarm, and the the water level reaches the high water mark again to start the motor. Laundry is started after the end of the drainage switch, when the water level reaches the low water level, then start the dehydration motors, rotating 2min. Repeat three times, each action requires the interval between the 2s. High water, low water level as water level sensors, with two analog switches, when the water

该程序是用来动态增减窗体上的控件的.方便在不同情况使用时去掉一些控件-that the procedure was used to dynamic changes in the Form of Control. Facilitate the use of different circumstances remove some controls ..

多功能数字钟设计 基本要求： 1.具有时，分，秒的显示。 2.时，分可以调整。 3.使闹钟具有可整点报时与定时闹钟的功能。 -Multi-function digital clock design basic requirements: 1. With hours, minutes and seconds display. 2. Hours, minutes, can be adjusted. 3. To be the whole point timekeeping clock with alarm and timer functions.

在PC机上，用汇编语言实现交通灯管理系统，包括路面，灯，车的动静态画面。-In the PC, using assembly language to achieve traffic light management system, including roads, lights, static and dynamic vehicle images.