Indoor real time Localization system based on Zigbee technologie using RSSI

交通灯： 1. 因为本设计是交通灯的控制，所以要先了解实际交通灯的变化规律。假设一个十字路口为东西南北走向。初始状态0为东西红灯，南北红灯。然后转状态1南北绿灯通车，东西红灯。过一段时间转状态2，南北绿灯闪几次转亮黄灯，延时几秒，东西仍然红灯。再转状态3，东西绿灯通车，南北红灯。过一段时间转状态4，东西绿灯闪几次转亮黄灯，延时几秒，南北依然红灯。最后循环至状态1。 2. 双色LED是由一个红色LED管芯和一个绿色管芯封装在一起，公用负端。当红色正端加高电平，绿色正端加低电平，红灯亮；红色正端加低电平，绿色正端加高电平，绿灯亮；两端都加高电平，黄灯亮。 急救车和交通灯： 中断服务程序的关键是：1. 保护进入中断时的状态，并在推出中断之前恢复进入时的状态；2. 必须在中断程序中设定是否允许中断重入，即设置EX0位。 本设计使用了INT0中断，一般中断程序进入时应保护 PSW，ACC以及中断程序使用但非其专用的寄存器。本设计中的INT0程序保护了PSW，ACC，2等三个寄存器并且在退出前恢复了这三个寄存器。另外中断程序中涉及到关键数据的设置时应关中断，及设置时不允许重入。本设计中没有涉及这种情况。 name:trled1.asm trled2.asm-traffic lights : 1. Because of the design of the traffic lights, so there must first understand the traffic lights change. Assuming a crossroads for the east-west north-south. Initial state of things 0 red light, red light north-south. Then the state opening of a north-south green, red things. For a period of time to state 2-green flashing yellow light switch several times, a few seconds delay, things are still red. Three sub-state, opening things green, red ligh

keil编译器的环境下基于lpc2378的各个模块的工程代码-keil compiler environment of each module based on lpc2378 project code

linux下基于9260的应用例程:norflash读写-application example(linux), based on atmel9260: norflash operation

这篇文档介绍在Linux下用GNU工具集开发ARM程序的一个机理-This document describes the use of GNU Linux development tool set procedures for an ARM Mechanism

print hello- microblaze

提供的程序是供四相步进电机使用。本实验使用的步进电机用直流+12V电压，电机线圈由A、B、C、D四相组成。 2. 驱动方式为四相单四拍方式,各线圈通电顺序如下表。表中首先向A相线圈输入驱动电流，接着向B，C，D线圈通电，最后又返回到A相线圈驱动，按这种顺序轮流切换，电机轴按顺时针方向旋转。若通电顺序相反，则电机轴按逆时针方向旋转。-provide for the procedures of the four-phase stepper motor use. This experiment used the stepper motor 12V DC voltage electrical coils A, B, C, D phase. 2. Four-driven approach to making four single-phase, the coil electrifying sequence the following table. Table A first phase coil input drive current, then to B, C, D coil electricity and eventually return to the A-phase coil driven by the rotation order of this switch, the electrical axis by rotating clockwise direction. If electricity in reverse order, the motor shaft by the anti-clockwise rotation.

ARDUINO LED矩阵不是我的

 #include "stm32f10x.h"#include "I2C_MPU6050.h"#include "usart1.h"#include "delay.h"int main(void){   InitMPU6050();/***********************************************************************/while(1){printf(" ---------------%d ",GetData(ACCEL_XOUT_H));printf(" ----------------%d ",GetData(ACCEL_YOUT_H)); printf(" ------------------%d ",GetData(ACCEL_ZOUT_H)); printf(" ---------------%d ",GetData(GYRO_XOUT_H)); printf(" -----------------%d ",GetData(GYRO_YOUT_H)); printf(" ---------Í---------%d ",GetData(GYRO_ZOUT_H));delay_ms(500);}  }/******************* (C) COPYRIGHT 2012 WildFire Team *****END OF FILE************/

DPIC30F6010A的头文件和连接文件，根据这两个文件可以完成寄存器C语言编程与汇编编程的对应！而且是工程中必须包含的文件！-DPIC30F6010A header files and link files, according to the two documents to be completed registers C programming and assembly language programming counterparts! But also project must include the file!

为优龙公司的2410开发板写的一个的AD采样驱动程序，-Liuzhou