登录
首页 » SCM » 12864显示程序(AVR串行接口),包括浮点数字显示功能

12864显示程序(AVR串行接口),包括浮点数字显示功能

于 2022-03-12 发布 文件大小:2.07 kB
0 156
下载积分: 2 下载次数: 1

代码说明:

12864显示程序(AVR串行接口),包括浮点数字显示功能-12864 display program (AVR serial interface), including floating-point digital display

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 基于altera公司的cycloneIII_3c25_niosII的应用程序软件,是altera公司提供的标准例程,里面包含sd卡的读写,位图在lcd的显示等。...
    基于altera公司的cycloneIII_3c25_niosII的应用程序软件,是altera公司提供的标准例程,里面包含sd卡的读写,位图在lcd的显示等。-On altera" s cycloneIII_3c25_niosII application software, is provided by altera standard routines, which contains the sd card reader, lcd display bitmaps and so on.
    2022-04-25 17:06:21下载
    积分:1
  • HCS08的AD例程:本程序是ADC模块的例程,所用资源为单片机内部ADC转换模块, 所接器件为电位器.
    HCS08的AD例程:本程序是ADC模块的例程,所用资源为单片机内部ADC转换模块, 所接器件为电位器.-HCS08 s AD routine: This is the ADC module of the routine procedure, the use of resources within the ADC conversion for the microcontroller module, the device is connected potentiometer.
    2022-03-14 02:11:59下载
    积分:1
  • 华为的印刷电路板(PCB)设计规范,程序编写规范等
    华为的印刷电路板(PCB)设计规范,程序编写规范等-Huawei’s printed circuit board (PCB) design specifications, programming specifications, etc.
    2022-11-09 12:45:03下载
    积分:1
  • 标准frescale单片机的I2C总线程序
    标准frescale单片机的I2C总线程序-frescale MCU standard I2C bus procedures
    2022-06-15 16:32:18下载
    积分:1
  • Is to introduce the use of single
    是介绍使用单片机控制led显示的程序,可以显示多种样式.-Is to introduce the use of single-chip control procedures led display, can display a variety of styles.
    2023-03-04 00:25:03下载
    积分:1
  • C8051F020 single
    c8051f020单片机串行通信口UART0使用-C8051F020 single-chip serial communication port UART0 to use
    2022-05-28 20:11:34下载
    积分:1
  • 用c51编的 键盘输入的乘法运算,增加语句可以增加功能
    用c51编的 键盘输入的乘法运算,增加语句可以增加功能-C51 series with the keyboard input of the multiplication to increase the sentence can increase the functional
    2022-02-26 12:49:33下载
    积分:1
  • PIC18F family some LCD driver
    Microchip PIC18F 设备驱动 LCD部分-PIC18F family some LCD driver
    2022-08-16 15:37:56下载
    积分:1
  • * Hardware architecture: PA0
    * 硬件结构: PA0-5对应6个LED数显管的位 ,PC0-7对应各LED数显管的段 ,PB4-7为键盘。 * 软件描述: 上电后,时钟从00.00.00(时/分/秒)自动走时,在走时状态时 , 按PB4(设定 * 键)超过3秒可循环选择调整时间/工作参数 ,接着按PB5以确定选择的操作 ,进入调整操作后 , * 按PB5选择欲调整参数,按PB6(增加键)完成调整参数操作 。按PB7,进入时控运行,PB1亮, * 再按PB7停止时控运行,回显走时。在定时到时,PB0点亮。- * Hardware architecture: PA0-5 corresponds 6 LED numbers to reveal the tube the position, PC0-7 corresponds each LED number to reveal the tube the section, PB4-7 is a keyboard. * Software description: After on electricity, clock from 00.00.00 (when/a minute/second) is in luck automatically, when is in luck the condition, according to PB4 (hypothesis * The key) surpasses for 3 seconds to be possible to circulate the choice time/operational parameter, then presses PB5 by to determine the choice the operation, after enters the adjustment operation * Wants according to the PB5 choice to adjust the parameter, (increases key) according to PB6 to complete the adjustment parameter operation.According to PB7, enters when controls the mov
    2022-04-16 19:29:12下载
    积分:1
  • 用ATMEL AVR单片机开发的MMC程式在SPI模式
    用ATMEL AVR单片机开发的MMC程式在SPI模式-with ATMEL AVR development programs in the MMC SPI mode
    2022-09-15 12:30:02下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载