MSP430系列单片机串口编程详细介绍，有实用的编例子和注释，很好的学习资料...

在80C51上实现USB2.0功能的源码-In the 80C51 functions to achieve USB2.0 source

at89s51的中文资料，方便单片机初学者学习参考，并且翻译质量基本上可以。-English at89s51 of information for beginners to study single-chip reference, and basically the quality of translation.

x5045相关程序，用keil c,其中附有两份很实用的资料-X5045-related procedures, using keil c, one with two very useful information

Adobe Audition数字存储示波器 利用电脑强大的处理能力和声卡高精度的AD/DA界面，加上Adobe Audition强大的录制和显示功能，数字存储示波器的功能即可轻易实现-Adobe Audition Digital Storage Oscilloscope use of computer processing power and high-precision sound card AD/DA interface, together with Adobe Audition powerful recording and display, digital storage oscilloscope functionality can easily realize

LT_1B msp430开发板例子程序－TB5

用于51系列的单片机开发时基本的7段数码管驱动源代码-51 Series Microcontroller for the development of basic paragraph 7, when the digital control-driven source code

单片机电路图.开发者可借助此51电路原理图，大大简化开发难度，提高效率。-Single-chip circuitry. Developers can take advantage of the 51 circuit schematic diagram, greatly simplified the development of the difficulty and improve efficiency.

WM-02U读卡器VBDEMO,非常好用哦

51汇编语言，格式为.chm文件，这个好象就是九十年代初孙涵芳（如果我没记错的话）写的一 本书后附的子程序。子程序不全对，至少有个除法的余数有问题，扩大了2倍，我记不清是哪个了，你把其中的一个左移语句去掉就行了，别的记不得了。欢迎常联系。-51 assembly language format. Chm documentation, It was like the early 1990s-wu (if I remember correctly so) wrote a book attached to the subroutine. Subroutine incomplete right, at least a division of the remaining problems, and expanded two times, I can not remember clearly what is, you put one of these bits removed statement on the visit, other reporters unnerving. Welcome regular contact.

三相步进电机的三相六拍工作方式，正转的绕组通电顺序：A、AB、B、BC、C、CA、A，反转的通电顺序：A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性，故步进电机的工作过程中不能及时的启动和停止，在启动时应慢慢的加速到预定速度，在停止前应逐渐减速到停止，否则，将产生失步现象。 步进电机的控制问题可总结为两点： 1、产生工作方式需要的时序脉冲； 2、控制步进电机的速度，使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.