-
本源代码通过一个按键控制LED的闪烁,使之可以看到单片机编程的基本要领...而且此源代码结构完整,格式精确...欢迎下载...
本源代码通过一个按键控制LED的闪烁,使之可以看到单片机编程的基本要领...而且此源代码结构完整,格式精确...欢迎下载
- 2022-03-13 07:11:03下载
- 积分:1
-
with C
用C-BASEIC语言编写的805X单片机计算子程序P=A0+A1*X+A2*X*X+A3-with C-language BASEIC the 805X MCU calculation subroutine P = A0 A1 A2* X* A3* X* X* X* X* X
- 2023-07-19 22:45:03下载
- 积分:1
-
12,232 drivers, drivers LCD YLF12232F
12232的驱动程序,驱动液晶YLF12232F-12,232 drivers, drivers LCD YLF12232F
- 2022-11-04 05:55:03下载
- 积分:1
-
门禁系统 interated with LCD
门禁系统 interated with LCD-Access Control System interated with LCD
- 2023-02-25 04:30:03下载
- 积分:1
-
This code has two wireless transceiver module prt8000 (core chip nrf905) of the...
本代码实现了两块无线收发模块prt8000(核心芯片nrf905)的通信功能-This code has two wireless transceiver module prt8000 (core chip nrf905) of the communication function
- 2022-09-19 19:05:02下载
- 积分:1
-
PHILIP的一双串口单片机的第2个串口的通讯例程
PHILIP的一双串口单片机的第2个串口的通讯例程-PHILIP pair of the serial microcontroller two serial communication routines
- 2022-04-27 08:56:28下载
- 积分:1
-
超声波测距模组使用说明书v1.0.pdf
超声波测距模组使用说明书v1.0.pdf-Ultrasonic Ranging Module Manual v1.0.pdf
- 2022-07-03 04:41:18下载
- 积分:1
-
基于中断控制的声光报警器的设计.采用中断方式,设计一个声光报警器的硬件电路和控制程序。程序运行时,一旦8位开关信号量状态满足设定条件,就触发中断,使发光二级管按...
基于中断控制的声光报警器的设计.采用中断方式,设计一个声光报警器的硬件电路和控制程序。程序运行时,一旦8位开关信号量状态满足设定条件,就触发中断,使发光二级管按规律闪烁,同时扬声器播放一段音乐。
硬件设备包括一台微机、一个MFID微机实验箱、一块T型板,2输入四与门 74ls08、8位总线驱动器 74ls245、LM386A音频放大器、排阻、扬声器各一个,发光二极管8个,470uF电容2个、104电容4个,插线若干。
-Interrupt-based control of sound and light alarm design. Using interrupt mode, designing a sound and light alarm hardware circuits and control procedures. The program is running, once the 8-bit switch signal to set the amount of state to meet the conditions to trigger interrupts, so that light-emitting diode flashes according to the law, while speakers play a piece of music. Hardware includes a computer, a computer simulation, MFID box, a T plate, 2 input 4 and gate 74ls08, 8-bit bus driver 74ls245, LM386A audio amplifier, exclusion, speakers of a light-emitting diode 8, 470uF capacitor 2 a, 104 capacitors 4, plug-line number.
- 2022-02-06 01:23:00下载
- 积分:1
-
密码锁的设计,单片机初学者必须程序,适用于proteus
密码锁的设计,单片机初学者必须程序,适用于proteus-Locks design, single-chip microcomputer program for beginners to be applicable to proteus
- 2022-01-23 10:40:29下载
- 积分:1
-
使用USB单片机做的应用,可以模拟三键鼠标,开发keil
利用51单片机做的USB 应用实例,可模拟三键滚轮鼠标,KEIL开发-use USB MCU do application, can simulate three key wheel mouse, development KEIL
- 2022-01-26 01:34:45下载
- 积分:1