Pwm control on an example, based on 8051f020 an example.

单片机系统上电后，P0 口和 P1 口都被清 0。然后，你规定一个由 6 个数字构成的序列（每个数字从 0～F 中选取），比如 E、8、9、0、7、F。然后每次当单片机检测到外部中断 0发起中断时间时，读取 P0 口和 P1 口上的状态值，当连续 6 次外部中断事件的对应的数字序列构成你所设定的序列后（举例来说，如果 P0.0 是 1，P0 和 P1 的其他管脚是 0，那么我们称为检测到一次数字 0），从串口打印输出一幅类似下图的 16×16 的ASCII码的圣诞树图片。-Single-chip microcomputer system after power, P0 and P1 mouth I have been ching 0. Then you set a six figure constituted by the sequence (each number from 0 ~ F in selected), for example, E, 8,9,0,7, F. And then each time a single-chip detects external interrupt 0 initiated interruption time, I read the P0 and P1 mouth on the state value, when a row 6 times the corresponding external interrupt events constitute digital sequence set your sequence (for example example, if P0.0 is 1, P0 and P1 of the other pin is 0, then we called a number of detected 0), a printout from the serial port under similar 16 × 16 map of the ASCII code of the Christmas tree图片.

单片机的应用及其原理-Theory and Application

本压缩文件主要介绍语音芯片ISD25120的使用方法，附有实用源代码，直接可以使用-This paper introduces the voice compression chip ISD25120 use with utility source code can be used directly

飞思卡尔智能车测试程序,仅仅是调试程序，没有完全通过-The test program for freescaleic interligentcar.

MSP430常用的程序源代码,很全的,一定适合你(初学者)!-MSP430 common source code, is full of, for you (beginners)!

【SoC单片机实验、实践与应用设计：基于C8051F系列】一书的光盘，里面有39个C8051F020的源码可供参考

这是一个输出字节和汉字的程序...可以用的我已调试过的-output byte characters and procedures can be used to ... I have tuned in

能够学会用单片机控制打印，还能深入了解单片机内部机理。-to learn how to use the SCM control print, but also in-depth understanding of the internal mechanism of SCM.

基于HS108设计的红外水位检测仪，内含C源代码，原理图及PCB，稍作改动可以用于很多位置检测场合如油泵位置检测等。-HS108-based design of infrared detector water containing C source code, schematics and the PCB, to make a minor amendment can be used for position detection in many occasions, for example, pumps and other position detection.

* 硬件结构： PA0-5对应６个ＬＥＤ数显管的位 ，PC0-7对应各ＬＥＤ数显管的段 ，PB4-7为键盘。 * 软件描述： 上电后，时钟从00.00.00（时/分/秒）自动走时，在走时状态时 ， 按PB4（设定 * 键）超过3秒可循环选择调整时间/工作参数 ，接着按PB5以确定选择的操作 ，进入调整操作后 ， * 按PB5选择欲调整参数，按PB6（增加键）完成调整参数操作 。按PB7，进入时控运行，PB1亮， * 再按PB7停止时控运行，回显走时。在定时到时，PB0点亮。- * Hardware architecture: PA0-5 corresponds 6 LED numbers to reveal the tube the position, PC0-7 corresponds each LED number to reveal the tube the section, PB4-7 is a keyboard. * Software description: After on electricity, clock from 00.00.00 (when/a minute/second) is in luck automatically, when is in luck the condition, according to PB4 (hypothesis * The key) surpasses for 3 seconds to be possible to circulate the choice time/operational parameter, then presses PB5 by to determine the choice the operation, after enters the adjustment operation * Wants according to the PB5 choice to adjust the parameter, (increases key) according to PB6 to complete the adjustment parameter operation.According to PB7, enters when controls the mov