F020 实现ADC 采样 串口输出到上位机

提供一个用 SST89E564RD 芯片控制直流电机转速的参考程序，如果哪位大虾有意见，欢迎给我电邮。-SST89E564RD provided with a chip speed DC motor control reference procedure, if any prawns have different views, I welcome e-mail.

1602A 显示的英文句子。实验板上已通过-1602A

简单的数据采集插值方法。-simple interpolation method of data acquisition.

单片机乒乓球游戏机 可以再proteus仿真，功能详细多样 给大家分享-Single-chip table tennis game can be Proteus simulation, functional detail for everyone to share diverse

用单片机 AVR mega48来模拟usb 很好的通讯方案-MCU AVR mega48 used to simulate the usb good communications program

AVR单片机中TWI(I2C)总线操作串行存储器24c02的C语言程序,如果要搞TWI串行总线的可以参考.程序总包括了单片机对24c02的写和读,用ICCAVR开发.-AVR MCU TWI (I2C) serial memory bus to operate 24C02 C-language procedure, if want to TWI Serial Bus can refer to. Procedures include single-chip microcomputer of the total 24C02 write and read, with the development of ICCAVR .

单片机串行E2PROM驱动大全-serial E2PROM- Daquan

Verilog实现的DDS正弦信号发生器和测频测相模块，DDS模块可产生两路频率和相位差均可预置调整的值正弦波，频率范围为20Hz-5MHz，相位范围为0°-359°，测量的数据通过引脚传输给单片机，单片机进行计算和显示。-Verilog realize the DDS sine wave signal generator and frequency measurement module test phase, DDS module can generate both frequency and phase difference can be preset to adjust the value of sine wave, frequency range of 20Hz-5MHz, phase range of 0 °-359 ° , measurement data and transmit them to the single-chip pin, single-chip microcomputer to calculate and display.

一个单片机仿真程序，并带有仿真文件，线路调试程序，及原理图。-a microcontroller simulation program, and with simulation, circuit debugging procedures and schematics.

程序描述：这个范例说明如何使用8051，以及汇编语言的程序连结， 当我们按下向上数的按钮之后，程序就会把0到9的共 阳7段显示器字型码存入AT93C46；如果我们按下向下 数的按钮之后，程序就会把9到0的共阳7段显示器字 型码存入AT93C46。 程序每一次重新开始执行时(Power on 或是Reset)，8051 会先从AT93C46当中读出最前面的10个位组，然后 就反复地将这10个位组的数据经由PORT 1送到1个 共阳七段显示器。*/-Procedure Description: This example shows how to use the 8051, as well as links to assembly language programs, when we pressed up a few of the button, the program will bring a total of 0-9 yang seven segment display font yards into AT93C46 if we press Next down the number button, the program will bring a total of 9-0 Yang seven segment display font code into AT93C46. Process to begin again each time when the (Power on or Reset), 8051 will start with AT93C46 were read out in front, 10-bit groups, and then repeated these 10-bit groups of data via the PORT 1 sent to a A total of seven-segment display Yang.* /