使用PIC12C508509的例程：用PIC12C508509 控制一个步进电机源程序，用PIC12C508A 控制模型源程序和用PIC12C509 控制LED...

我自己写的一个tcp/ip的代码，很短，用的是vc来做模拟调试的，具体的运行是要在mcs51单片机上的，只有一个端口。具体请大家看程序吧！-I wrote it myself a tcp/ip code, in a very short, it was vc do simulation testing, the specific operation is to mcs51 MCU, only one port. Please refer to specific procedures!

TMX320TCI6482 电路图，很难得才弄到！-TMX320TCI6482 circuit, it is difficult to have to get before!

液晶显示控制器T6963C与单片机的接口及编程-T6963C LCD controller and microcontroller interface and programming

超小gps+msp430的部分原代码,有需要的普有可以-Ultra-small gps+ Msp430 part of the original code, there is a need to have the S

该程序为基于51单片机的接口和片外应用的代码，在设计51单片机时可供参考，代码包括RS232通信、I2C、SPI、单总线、CAN总线、键盘、LED、LCD、AD/DA等应用。各工程在Keil调试通过，喜欢的朋友可供参考。-The program is based on the 51-chip microcontroller interface and application code, in the design of microcontroller 51 when the reference code, including RS232 communication, I2C, SPI, single-bus, CAN bus, keyboard, LED, LCD , AD/DA applications. Keil debugging the project passed, like a friend for reference.

关于51单片机DS18B20的驱动程序，编译过，可以直接使用。-About 51 Singlechip DS18B20 driver, compiler, and can be used directly.

基于89C51单片机的洗衣机控制器，含SCH电路图以及C程序-Based on the 89C51 single-chip controller of the washing machine, including schematics, as well as C procedures SCH

用C8051F020编写的RA8803控制器320240液晶程序-C8051F020 prepared with RA8803 LCD controller 320,240 procedures

这是一个AVR单片机的电子教程，对于初学AVR单片机的人来说是个比较不错的资料！-This is a single-chip electronic AVR tutorials for beginners who AVR MCU is a relatively good information!

本设计主要是运用单片机设计一个最小系统――电子时钟，它具有24小时计时功能，能够对时间进行调整，并且能实现时、分、秒的显示，同时还有内设闹钟，时间到时候会响铃，响铃时可以通过按键控制延时再启动或关断。与此同时还设置了整点报时功能；并采用采用了软件去抖的方法扫描键盘，动态刷新显示数码管，并通过查表实现译码输出时间等编程方法；-This design is the use of single-chip design of a minimum system- Electronic clock, it has a 24-hour timer function, capable of time to adjust, and can achieve the hours, minutes and seconds display, but also equipped with alarm clocks, time to When ringing the bell to ring when the button control can delay re-start or shutdown. At the same time also set up the whole point timekeeping function and adopt the use of the software to scan the keyboard shaking method, dynamic refresh display digital tube, and through the realization of decoding look-up table output time programming method