用51单片机c语言编写的键盘扫描程序

在网上找的，所以的关于MAX260，MAX261，MAX262，MAX263的中文资料及很多实例程序和经典电路-Online to find, therefore, on the MAX260, MAX261, MAX262, MAX263 Chinese information and a lot of examples of procedures and the classical circuit

1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序, 测试精度为0.1秒，按 SW1键启动计数，再按一次 SW1键停止计数。任何时候按 SW3 键停止计数，并对计数值清零。 4．按 SW1键后， 以 0.1 秒为单位开始计数，再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒，则计数值清零，回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.

* 硬件结构： PA0-5对应６个ＬＥＤ数显管的位 ，PC0-7对应各ＬＥＤ数显管的段 ，PB4-7为键盘。 * 软件描述： 上电后，时钟从00.00.00（时/分/秒）自动走时，在走时状态时 ， 按PB4（设定 * 键）超过3秒可循环选择调整时间/工作参数 ，接着按PB5以确定选择的操作 ，进入调整操作后 ， * 按PB5选择欲调整参数，按PB6（增加键）完成调整参数操作 。按PB7，进入时控运行，PB1亮， * 再按PB7停止时控运行，回显走时。在定时到时，PB0点亮。- * Hardware architecture: PA0-5 corresponds 6 LED numbers to reveal the tube the position, PC0-7 corresponds each LED number to reveal the tube the section, PB4-7 is a keyboard. * Software description: After on electricity, clock from 00.00.00 (when/a minute/second) is in luck automatically, when is in luck the condition, according to PB4 (hypothesis * The key) surpasses for 3 seconds to be possible to circulate the choice time/operational parameter, then presses PB5 by to determine the choice the operation, after enters the adjustment operation * Wants according to the PB5 choice to adjust the parameter, (increases key) according to PB6 to complete the adjustment parameter operation.According to PB7, enters when controls the mov

PID是控制智能小车的经典算法在过程控制中，按偏差的比例（P）、积分（I）和微分（D）进行控制的PID控制器（亦称PID调节器）是应用最为广泛的一种自动控制器。它具有原理简单，易于实现，适用面广，控制参数相互独立，参数的选定比较简单等优点；而且在理论上可以证明，对于过程控制的典型对象──“一阶滞后＋纯滞后”与“二阶滞后＋纯滞后”的控制对象，PID控制器是一种最优控制-PID control of the smart car is the classic algorithm in process control, according to the percentage of deviation (P), Integral (I) and differential (D) control of PID controller (also known as PID regulators) is the most widely used as a automatic controller. It has simple, easy to realize, the application of a wide range of control parameters are independent of each other, the selection of relatively simple parameters, etc. and in theory can be proved that for a typical process control objects ─ ─

AVR对液晶12232串行读取LCD12232上有个并口与串口跳线请选串口-LCD AVR 12232 Serial to read LCD12232 There is a parallel port and serial jumper Please check serial

modbus通信协议范例,详细解答了modbus的通信方式,如读线圈、寄存器…-Modbus communication protocol example, detailed answers to the Modbus communication methods, such as reading coil, register ...

单片机关于静态液晶显示的小程序，大家看看吧，说不定有用-Single-chip liquid crystal display on the static small program, let us look at it, maybe useful

做的一个FFT算法原程序与大家共享，内有较祥细的说明-do an FFT algorithm for the original procedures and share, compared with a wound Note

可调万年历led版:led数码显示时间及温度，时间随时可调。-Adjustable calendar led Edition: led digital display time and temperature, time adjustable at any time.

用winband78e58 对422通讯操作，422通讯作为工业常用的串行通讯协议，使用广泛-with winband78e58 communications operation of 422, 422 communications industry as a common serial communication protocol, widely used