mcf522xx EV Board driver source code can be used directly. The driver I tested.

移植到MCS51的uCOS_II。 1。在文件OS_CORE.C中OSMapTbl和OSUnMapTbl数组用于查表，所以应该放在code里。 增加code关键字。UCOS_II.H和OS_CORE.C。 2。OS_CFG.H堆栈大小MaxStkSize改为900。 3。OS_CPU_C.C的InitTimer0函数增加了关于开T0中断的解释。 允许T0中断，此时EA=0(51上电缺省值)，中断还不会发生，满足在OSStart()前不产生中断的要求。 4。修改中断处理流程，以便严密监视中断嵌套情况。每个中断进入后立即进行OSIntNesting+1原语操作。 5。增加printf函数的移植，支持灵活的数据显示。支持标准或长二进制/八进制/十进制/十六进制/无符号整数， 支持字符、字符串、浮点数、百分号％。其中，浮点数在整个范围内被完全支持，统一采用科学记数法显示。 -transplanted to the MCS51 uCOS_II. 1. In the document which OSMapTbl OS_CORE.C and OSUnMapTbl array for Lookup, Therefore, it should be placed on code Lane. Increased code keyword. UCOS_II.H and OS_CORE.C. 2. OS_CFG.H MaxStkSize stack size to 900. 3. OS_CPU_C.C InitTimer0 function of the increase on the open T0 interrupted explained. Allow T0 interruption, this time EA = 0 (51 electricity default value), also will not be interrupted. meet the OSStart () do not have interrupted the former requirements. 4. Changes interrupt handling procedures, in order to closely mon

ucOs-ii完整源代码，极其方便用户调用-ucOs-ii complete source code, an extremely user-friendly call

UC/OS-II上调用时间管理函数实现时间管理的使用(UC/OS-II on the use of time management to achieve)

ucosII在atmega64上的移植基于WINAVR-atmega64ucosII

TG12864 LCD代码 在UC/OS 下 EASYRARM2100 下跑过，显示一个图形，程序在ADS1。2下运行。是个处女做，仅供参考-Source code of TG12864 LCD driver for uC/OS tested on EASYRARM2100. It can display an image on the screen. It has been tested on ADS1.2. My first program.

UCGUI实际的性能由许多因素决定, 如处理器/编译器/内存模 式/优化程度/配置/LCD 控制器连接方式等. UCGUI 在典型目标系统上的 性能测试参数和资源占用的分析报告, 通过报告你也可以获知在其它大部分目标系统上 情况(UCGUI actual performance is determined by many factors, such as the processor/compiler/memory mode/optimize the degree/configuration/LCD controller connection. UCGUI typical target system performance test parameters and resource consumption analysis report by report You can also be informed of the situation in most of the other on the target system)

MiniTerm STM32 ucGui

在mc9s12dg128b开发的ucos_-develop ucos_ii on mc9s12dg128b

LPC2300 网络驱动 KSZ8041NL-LPC2300 Network Driver KSZ8041NL

Can总线的控制协议，主要是用来实现以Can总线协议的方式进行的数据传输-Can Bus control protocol is primarily used for Can bus protocol in order to realize the way the data transmission