MSP430F413的各模块实例程序源代码，很方便调试。

使用键盘上的上、下、左、右四个按键，可以分别控制led1,2,3,4, 每个LED 对应的Port 请参考“实验平台介绍”说明文档。要求按下 上面提到的四个按键中间的一个按键后，该按键对应的led 被点亮，持续1 秒钟以后led 熄 灭。-Use the keyboard on the upper and lower, left, and right buttons, can control led1, 2,3,4, each LED corresponding to the Port, please refer to " experiment on" documentation. Requirements of the four above-mentioned press the middle button of a button, the button that corresponds to being light led, continuous 1 second later led out.

本程序用于用单片机控制步进电机的转动。用单片机的某一个引脚实现控制，如果引脚电平为高则实现正转，反之为反转。所用单片机为日立系列h83664十六位单片机。本代码使用c语言实现，开发环境为日立系列单片机专用开发环境-This procedure for the use of single-chip stepper motor rotation control. With a pin MCU control, if the pin level is higher then realize to the contrary, for the inversion. Used in single-chip for Hitachi Series 16 Singlechip h83664. This code uses the c language, development environment for the Hitachi series of single-chip dedicated development environment

单一灯的左移右移分别接在单片机的P1.0－P1.7接口上，输出“0”时，发光二极管亮，开始时P1.0→P1.1→P1.2→P1.3→┅→P1.7→P1.6→┅→P1.0亮，重复循环-A single light, respectively, shifted to right then left at P1.0-P1.7 microcontroller interface, the output " 0" when the bright light-emitting diode, the beginning of P1.0 → P1.1 → P1.2 → P1. 3 → ┅ → P1.7 → P1.6 → ┅ → P1.0 Liang, repeat cycle

本装置是一个以HT46R71D 为主芯片，配合传感器组成的汽车轮胎气压检测装 置，最终取高三位有效值于LCD 显示，有四种显示单位供切换（Psi、Bar、Kpa、 Kgf/cm2）。本装置仅为参考范例，使用时，为提高准确度，建议多量测些组数 据来构建Sensor Output Voltage - Discharge Time (V-T)表格，并作相应校准。-This device is a HT46R71D-based chips, with sensors detecting vehicle tire pressure devices, and ultimately take the high-three RMS in LCD display, there are four types of display units for switching (Psi, Bar, Kpa, Kgf/cm2). Only reference to an example of the device, when used to improve the accuracy of the proposed多量measured set of data to build more Sensor Output Voltage- Discharge Time (VT) forms, and the corresponding calibration.

LUMINARY ARM的正交编码的代码-Orthogonal coding LUMINARY ARM code

CP2200中文手册，不错的东西，不错的东西-CP2200_cn good good good good good

3.多路舵机控制电路C语言版 C51-3. Multi-channel steering gear control circuit C language version of C51

MSP430F20xx的汇编程序示例，包括定时器范例、比较器范例-MSP430F20xx the assembler sample, including the timer example, comparator example

串口通信，单片机识别窗口之间通信，使用的是STI51-Serial communications, single-chip communication between the identification window, using STI51

关于2407的sci串口扩展实现dsp的串行通信以及关于地址的问答-on the 2407 sci Serial Port Expansion achieve dsp serial communications and addresses on the Net