用ATMEGA8开发的MMC程式,可用AVR

在keil环境下编写的，仿真用protuse。 很适合初学者 两个51单片机通讯，并且显示对方的信息-In keil prepared environment, simulation using protuse. Very suitable for beginners and two 51 Singlechip communications, and show each other

这是ATMEL公司，的AT9200的LOADE程序让你们感受一精简指令集的冲击-This is ATMEL Corporation, the AT9200 LOADE the procedures so that you feel a RISC impact

用C8051F020读取红外遥控，采用扫描的方法-C8051F020 read with infrared remote control, using the method of scanning

TECHWELL 之tw2835 四画面合一之驱动代码,CCIR656输出,KEIL C51 平台编译,-Techwell tw2835 of one of four screen-driven code, CCIR656 output, KEIL C51 compiler platform,

工程师在用Keil开发程序时，在代码性能要求较高的场合，需要对代码段的执行时间作统计。比如在做LED显示屏软件扫描程序，或一些定时采集数据程序，如果在软件仿真的时候就能够清晰知道代码段的运行时间，那就可以对程序进行优化，或者插入汇编代码(asm)达到最高运行速度。 关键字:Keil DLL C语言 ASM 汇编-engineers in the development process with Keil, the code performance requirements higher occasions, need to block the execution time statistics. For example, in the software do LED scanning procedures, or some regular data collection procedures, If the software simulation time can understand clearly code of the running time, it can process optimization, or insert code compilation (asm2) to achieve maximum speed. Keywords : Keil DLL C language compilation ASM

三星2410芯片中定时器和产生内部中断，及其使用-Samsung 2410 chip timers and an internal interrupt, and its use

我上传的一些单片机的资料，KEIL软件的使用，希望对大家有帮助-I uploaded some information on SCM, KEIL software, I hope all of you help

这是一个波形选择菜单，通过开发板上的按键，选择波形，幅度，频率的等各参数，然后发送给下位机。让其产生需要的波形。-This is a waveform selection menu, through the development of on-board buttons, select the waveform, amplitude, frequency and other parameters, and then sent to the next bit plane. The need to generate the waveform.

用单片机不同的IO口驱动数码管，以解决IO口不是一个PO口的问题。-Microcontroller IO port with a different drive digital tube, to address the IO port is not a PO mouth problem.

6段数码管分别显示，时，分，秒，四个按键，K1（P0.0），K2（P0.1）， K3（P0.2），K4（P0.3），四个按键用来调时间的，按下K1，所有位都清零显示，然后按下K2，秒在闪烁，继续按K2分闪烁，不段地按K2 秒--分--时切换着闪烁，在某位闪时按下K3相应位加一，确认调整，按K4，取消调整再按K1。在K1按下以后才有调时的功能，如果K1没有按下，按别的键没有反映。这为了在加点按键功能留着用 -6 respectively of the digital control, when, minutes and seconds, four keys, K1 (P0.0). K2 (P0.1), K3 (P0.2), K4 (width), the four keys to the transfer time, press the K1, All spaces are reset, then press K2, the scintillation seconds, according to K2 pm flickered. not according to K2 of seconds-- minutes-- when switching to flicker in certain press the flash-K3 corresponding increase in a confirmed adjustment by K4, then canceled K1 adjustment. K1 in the press will only be made after the transfer of function, if K1 pressed by other key is not reflected. This points to the function keys used Retention