SEED_DEC5416的FLASH的boot程序源码

包含AM调制，DFT，256FFT，FIR和IIR，另外包含所需的子文件Surport，程序都比较精炼，特别适合DSP初学者上手-AM modulation includes, DFT, 256FFT, FIR and IIR, the other contains a subset of the required documents Surport, procedures are more refined, especially suitable for beginners to use DSP

tms320lf2407串行外设接口模块程序，希望对学习dsp的朋友能有所帮助

基于DSP ti tms 320lf 2407的 电压矢量变频调速源程序 运行于 ti 公司的 ccs2.2 -Based on DSP ti tms 320lf 2407 VVVF voltage vector of the source code running on the ti

tms320lf2407a　利用自带片上10位AD实现AD采样　执行FFT算法已经得到验证-TMS320LF2407A use its own on-chip 10-bit AD sampling AD realize the implementation of FFT algorithm has been tested

DSP2812ADC - 测量两个模拟输入电压, 每个0.1sec由通用定时器1出发一次ADC转换；看门狗使能，在主函数循环以及ADC的中断服务程序中处理-DSP2812ADC- measurement of two analog input voltage, 0.1sec each one starting from a general-purpose timers ADC conversion Watchdog enable, in the main function of the cycle as well as the ADC interrupt service routine in the treatment

工程示例说明 //1.本示例实现一个按键状态的检测,并通过相应的按键状态来控制LED灯的亮灭; //2.本示例中使用的按键是K3,它的控制端口是GPIO32,硬件上有一个上拉电阻,所以按键未按下时为高,按下后为低; //3.代码执行流程: //  3.1 首先是系统时钟的选择,这里我们选取的是外部无源时钟(10MHZ),他通过12倍频后再2分频最终得到60MHZ的系统时钟 // 3.3 然后是PIE中断向量表的初始化 //  3.2 接下来是一些外设的初的初始化,如果使用flash固化模式,还要执行一些flash相关的操作; //  3.4 最后是一个while(1)超级循环,这里实现按键的检测和LED的亮灭控制。 //4.其他说明 //  4.1 该示例在上一个工程模板的基础上新增加了一个Delay模块,这个模块实现的延时函数是基于汇编级US延时单元的,所以 //     &

合众达公司VPM642版的平台音频测试程序-Tatsu VPM642 united company a platform for the audio version of test procedures

DSP捕获历程，可以使DSP开发者尽快了解捕获功能的使用-DSP capture history, DSP developers can capture as soon as possible to understand the use of

DSP快速pwmDSP快速pwmDSP快速pwmDSP快速pwmDSP快速pwmDSP快速pwmDSP快速pwmDSP快速pwmDSP快速pwmDSP快速pwmDSP快速pwm

DSP/BIOS Driver Developer Kit 1.11 The DSP/BIOS Driver Developer Kit (DDK) provides a selection of pre-tested DSP/BIOS device drivers, and documentation on how to write a driver to the DSP/BIOS driver model, known as IOM. The DDK includes C source code for all drivers. The DDK 1.11 has been validated with CCS 3.1 and DSP/BIOS 5.20. -DSP/BIOS Driver Developer Kit 1.11 The DSP/BIOS Driver Developer Kit (DDK) provides a sel ection of pre-tested DSP/BIOS device drivers, and documentation on how to write a driver to the DSP/BIOS driver model, known as IOM. The DDK includes C source code for a ll drivers. The DDK 1.11 has been validated with CCS 3.1 and DSP/BIOS 5.20.