3、数据。FTAM是ISO标准协议的成员。交叉

CDMA中PN、Walsh码应用及调制解调的仿真实现-CDMA in the PN, Walsh code modulation and demodulation application and the Simulation

I2C 通信中只涉及两条信号线，即时钟线 SCL 和数据线 SDA。时钟线为高电平时均可锁存数据（即时钟线上升沿到下降沿之间）。当时钟线 SCL 高电平时，如果把数据线 SDA 从高 电平拉到低电平，则表示通信开始；如果把数据线 SDA 从低电平拉到高电平，则表示通信结束。 代码中分了两个模块，iic_com 模块除了执行和 I2C 通信有关的代码设计外，还有按键检测部分，而 led_seg7 模块只是驱动数码管显示从 AT24C02 指定地址读出的数据。

ROC curves illustrate performance on a binary classification problem where classification is based on simply thresholding a set of scores at varying levels. Lenient thresholds give high sensitivity but low specificity, strict thresholds give high specificity but low sensitivity the ROC curve plots this trade-off over a range of thresholds (usually with sens vs 1-spec, but I prefer sens vs spec this code gives you the option). It is theoretically possible to operate anywhere on the convex hull of an ROC curve, so this is plotted too. The area under the curve (AUC) for a ROC plot is a measure of overall accuracy, and the area under the ROCCH is a kind of upper bound on what might be achievable with a weighted combination of differently thresholded results from the given classifier -ROC curves illustrate performance on a binary classification problem where classification is based on simply thresholding a set of scores at varying levels. Lenient thresholds give high sensitivity but

提供了一个硬判决的viterbi译码器（2，1，3） 有源程序及算法描述，未成定稿，只供参考 （vhdl 语言描述） -provided a hard decision of the Viterbi Decoder (2,1, 3) the source code and the algorithm description, from his position as final, for reference (vhdl Description Language)

IEC61970数据集成规约扩展与应用。 IEC61970-IEC61970

一款配和短信模块报警的软件程序,参考一下吧-Allocation and a warning message Module software program, refer to it

清除除校准信息、SN、IMEI以外NVRAM里所有的数据 使用说明: 1.进入程序后点击BB Chipset下拉菜单，选择正确的Baseband芯片 2.点击浏览按钮，在弹出的对话框中选择与手机软件相对应的NVRAMDATABASE文件(SRC) 3.选择正确的串口后点击确定按钮，然后把手机接到串口线上等待状态栏显示为PASS后即可-In addition to calibration information clear, SN, IMEI outside all the data NVRAM for use: 1. To enter the program BB Chipset Click the drop-down menu, choose the correct Baseband chip 2. Click the Browse button in the pop-up dialog box, select and cell phone software corresponding to the NVRAMDATABASE document (SRC) 3. Select the correct serial port and click the OK button, and then received a serial line waiting for the phone displays in the Status column immediately after PASS

GE公司的103规约测试软件，请大家保密啊-GE IEC103 TEST

使用jsr284模块编写的控制手机摄像头的程序，实现了基本的拍照和保存。-use jsr284 to control camera in mobile phone.

H.264 over IP. Useful document for H.264 over IP. Published by IEEE.