登录
首页 » 嵌入式系统 » 液晶自模点阵提取软件

液晶自模点阵提取软件

于 2022-02-21 发布 文件大小:131.77 kB
0 194
下载积分: 2 下载次数: 1

代码说明:

液晶自模点阵提取软件-dot matrix LCD module from the extraction software

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 一个运行在PIC上的WEB服务器
    一个运行在PIC上的WEB服务器-a run in the PIC Web server
    2022-01-31 05:35:55下载
    积分:1
  • ads mpc860上hdlc的驱动程序,不带操作,属于纯粹的物理驱动...
    ads mpc860上hdlc的驱动程序,不带操作系统,属于纯粹的物理驱动-hdlc up ads mpc860 driver, non-operating system, belong to a purely physical drive
    2022-10-21 23:55:02下载
    积分:1
  • stm32 TCP-IP C/S模型例程
    展示了STM32单片机和计算机作为一个基于TCP-IP协议的C/S模型 通过网页控制STM32开发板上的led灯的亮灭 以太网芯片是enc28j60
    2022-04-19 23:28:21下载
    积分:1
  • MCUProductionProgrammer_Silicon
    MCUProductionProgrammer  Silicon Lab In-system programming  involves programming devices after installation inthe end system. In this scenario, access to the debug pins (JTAG or C2 interface) is provided in the end system to enable connection to a programming “Master”. This pro-gramming “Master” can bea Silicon Labs Serial Adapter (EC2), custom hardware, or for JTAG devices, a JTAG Boundary Scan test system that supports the programming ofSilicon Labs devices.
    2022-08-05 18:50:27下载
    积分:1
  • 液位检测程序,可做到四级灵敏度,通过短路冒实现
    液位检测程序,可做到四级灵敏度,通过短路冒实现-Liquid Level Detection procedures, four sensitivity can be achieved through the realization of short-run
    2022-12-24 21:45:08下载
    积分:1
  • gfhfhdghgfhgfh
    FDHGFHFGBSGSDHJGDSJKLFG公司
    2022-07-24 11:23:04下载
    积分:1
  • 网络处理器例子程序1
    网络处理器例子程序1--Example 1 for network programming.
    2023-08-04 08:10:03下载
    积分:1
  • 发光二极管
    应用背景写以下程序闪烁的发光二极管:关键技术下载手臂板上的程序和执行的结果。
    2022-02-13 00:34:23下载
    积分:1
  • 时钟芯片PCF8591 C语言程序
    时钟芯片PCF8591 C语言程序--C program for timer chip PCF8591.
    2022-10-16 19:45:03下载
    积分:1
  • L298N是ST公司生产的一种高电压、大电流电机驱动芯片。该芯片采用15脚封装。主要特点是:工作电压高,最高工作电压可达46V;输出电流大,瞬间峰值电流可达3A...
    L298N是ST公司生产的一种高电压、大电流电机驱动芯片。该芯片采用15脚封装。主要特点是:工作电压高,最高工作电压可达46V;输出电流大,瞬间峰值电流可达3A,持续工作电流为2A;额定功率25W。内含两个H桥的高电压大电流全桥式驱动器,可以用来驱动直流电动机和步进电动机、继电器线圈等感性负载;采用标准逻辑电平信号控制;具有两个使能控制端,在不受输入信号影响的情况下允许或禁止器件工作有一个逻辑电源输入端,使内部逻辑电路部分在低电压下工作;可以外接检测电阻,将变化量反馈给控制电路。使用L298N芯片驱动电机,该芯片可以驱动一台两相步进电机或四相步进电机,也可以驱动两台直流电机。-L298N is produced by ST a high-voltage, high current motor driver chip. The chip uses 15-pin package. Main features are: high voltage, the maximum working voltage up to 46V output current, instantaneous peak current up to 3A, continuous operating current of 2A rated power of 25W. Contains two H-bridge high-voltage high-current full-bridge driver can be used to drive DC motors and stepper motors, relay coils and other inductive load using standard logic level signal control has two enable control terminal, input signal without affecting the case to permit or prohibit the device work a logic supply input, so that part of the internal logic circuits at low voltage work can be an external sense res
    2022-02-05 00:53:15下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载