射频卡的读写程序，C #版，绝对闻所未闻，该卡可以读…

串口通讯在客户端/服务器类型的应用程序设计中经常要使用到，目前串口通讯采用的一般是专用软件包或者标准串口通讯协议(如XMODEM、ZMODEM等)，这样完整详细且免费的软件包比较少，所以在SPCOMM的基础之上建立了本文所描述的串口通讯协议，称之为RCC(表示为Reliable Comm Communication)，其主要目标是在用串口进行通讯的客户端/服务器双方建立一条可靠的通讯链路，就象TCP(RFC793)一样。该协议的目前的开发是采用VC++，应用平台为WIN95/NT，但作为RCC协议的本身不受具体编程语言及操作系统所限制-Serial port communication in client/server type of application design often use to the current serial communication is generally used in special packages or a standard serial communication protocols (such as XMODEM, ZMODEM, etc.), such a complete package details and free more less so on the basis of established SPCOMM described in this article serial communication protocol, called RCC (expressed as a Reliable Comm Communication), whose main objective is to communicate with the serial port client/server sides to establish a reliable communication link, like TCP (RFC793) the same. The current development of the protocol is used VC++, application platform for WIN95/NT, but as the agreement itself, RCC concrete programming

串口调试精灵，可以收发ASCII和HEX两种格式的数据，简单实用。-serial debugging genies, TX ASCII and HEX both formats of data, simple and practical.

本程序是i2c总线读写一个字节的程序。在写过程序中，不一定非要检测i2c的应答位，可以直接延时过去就行，但是在读过程中必须给应答信号，读完发停止位，一定确认所发的信号都发上了。否则在连续地址读的过程中可能不会出错，但是在随机度过程中就会出错，我的程序就是在给停止信号时没有给上，24cxx一直在输出数据，结果读出错。找着问题后我的程序只加入了一条命令便完全正常。-i2c bus read and write a byte procedures. The written procedure, not necessarily require the detection i2c-response, and can directly past trip delay, but the process must be read to the response signal, stopped at reading, we recognize the signals are on the fat. Otherwise, the address read for the course could not go wrong, but the randomness of the process would be a mistake, I was in the process to stop for no signal, 24cxx in output data, read errors. I discovered the problem after the procedure just joined the order of a completely normal.

手机模块gr47的各种操作源码，包括pdu格式转换等-phone module gr47 the various operational source, including pdu format converter, etc.

采用C语言,软件模拟硬件UART端口,基于PIC系列处理器实现.-Using C language software simulation of hardware UART ports, based on the PIC family of processors to achieve.

Viertex 2 开发板的接口程序，使用VC编写。-100 2 development board interface, the use of VC prepared.

在VB下对串口COMM控件编程和发机制进行了详细地设计，同时可以为串口调试用，不失为一个好工具。习惯于VB编程的朋友可以CC一下了。-in VB Serial COMM under the control programming and the mechanisms to perform detailed design, while it used to debug serial port, is a good tool. Accustomed VB CC friends out.

一个非常完整的川口通讯源程序，我费了很大功夫才把他找到。-a very complete source Kawaguchi communications, I spent a lot of time and energy only to find him.

在ADI公司的blackfin533开发平台上实现串口通信的程序代码-In the ADI" s blackfin533 development platform to achieve serial communication program code

在Windows CE上用串口采集数据并绘制成曲线,适合于数据采集,硬件平台是ARM开发板-在Windows CE上用