计算机接口技术系列 Visual C++串口通信技术与工程实践 在编译本章程序后，请将winio.dll、winio.vxd和winio.sys文件复制到可执行...

串口通讯，一个小程序，用Mscomm做的-serial communications, a small program to do with Mscomm

本程序是i2c总线读写一个字节的程序。在写过程序中，不一定非要检测i2c的应答位，可以直接延时过去就行，但是在读过程中必须给应答信号，读完发停止位，一定确认所发的信号都发上了。否则在连续地址读的过程中可能不会出错，但是在随机度过程中就会出错，我的程序就是在给停止信号时没有给上，24cxx一直在输出数据，结果读出错。找着问题后我的程序只加入了一条命令便完全正常。-i2c bus read and write a byte procedures. The written procedure, not necessarily require the detection i2c-response, and can directly past trip delay, but the process must be read to the response signal, stopped at reading, we recognize the signals are on the fat. Otherwise, the address read for the course could not go wrong, but the randomness of the process would be a mistake, I was in the process to stop for no signal, 24cxx in output data, read errors. I discovered the problem after the procedure just joined the order of a completely normal.

BCB串口通讯源码示例程序。利用winapi函数，而非控件。-BCB examples of serial communication program source. Use WINAPI function, rather than control.

本文讲述的利用通讯控件发送与接收通讯数据都是基于二进制来实现的，基于文本的情况基本与此类似。要想利用好通讯控件还有其他一些应该注意的地方，比如波特率的设置、接收与发送缓冲区的设置以及通讯过程中的延时问题的处理等等。-This paper describes the use of communications controls send and receive communications are based on the binary data to achieve, based on the basic text of this and similar. To make good use of communication controls should also pay attention to some other place, such as baud rate settings, receiving and sending the buffer settings and communication latency in the process of dealing with such problems.

非常好的串口通信程序,VC工程,只需要在此基础上稍做修改就可以加入到你自己的程序中-very good serial communication program, VC works only on this basis can be tailored to your own accession process

C51单片机串行口中断服务程序2,is used-C51 monolithic integrated circuit serial mouth interrupt service isr 2, is used

无线数传电台串口通信C程序源码 电台型号为深圳友迅达公司的F201/B无线数传电台-wireless radio-C serial communications procedures source model of Shenzhen Radio Xun-da Friends of the F201/B wireless radio transceiver

一个读取支持modbus协议的设备的数据工具-read a support agreement modbus connection equipment for the data tools

本文介绍的用 89C51 单片机I/O 口模拟实现串行通信的方法，已成功 地应用在某电压数据采集系统中，实践证明能可靠地传送和接收数据。-This article describes using 89C51 microcontroller I/O port Serial communication simulation method has been successfully applied in a certain voltage data acquisition system, the practice has proven to be a reliable way to send and receive data.

这是一款VC++编写的软件，包括手机发送信息及电话号码簿的一般例程-This is a VC++ Preparation software, including mobile phones to send messages and telephone directory general routines