本程序是用Keil c51 和Protues 联合开发的推箱子的小游戏，采用的87C51芯片，采用8×8位点阵液晶显示人物和箱子，每个点都是16×16位点阵。...

此模块是我在以前公司做热风枪项目时设计的一个模块，用于实时显示当前温度，其精度可以达到1摄氏度，三位半液晶显示，界面美观，稍作改动也可用段码LED作为显示。 程序功能：10位A/D的温度采集（热电偶）；TN段码液晶驱动；温度补偿； 文件包括：所有C源程序；完整的项目文件包（基于MCU：HT46R23） PCB HT46R23 DATASHEET 三位半液晶片DATASHEET-This module is in my hot air gun to do before the company projects a module designed for real-time displays the current temperature, its accuracy can reach 1 degree Celsius, three semi-liquid crystal display, interface aesthetics, make a minor amendment to paragraph can also be used as a code LED display . Program features: 10-bit A/D Acquisition temperature (thermocouple) TN LCD driver code segment temperature compensation documents include: All C source code complete package of project documents (based on the MCU: HT46R23) PCB HT46R23 DATASHEET 3 semi-liquid crystal film DATASHEET

用于汽车遥控的Ev1527的pic单片机软件接收解码程序，密码采用I2C总线方式存在EEPROM中-Remote control for automotive Ev1527 the pic Singlechip software decoder to receive the procedure, the password using I2C bus EEPROM in existence

PC机与单片机串口通讯可以通过多种方式来实现，在这里只介绍使用MSCOMM控件进行通讯。-PC and microcontroller serial communications to be many ways to achieve here in only MSCOMM controls on the use of communication.

在dsPIC30F和FYD12864平台的汉字和图形显示-In the dsPIC30F and FYD12864 platform ,graph and Chinese characters display

avrrice软件用于AVR单片机的JTAG调试.-avrrice software for AVR JTAG debugging.

内容：1、本程序用于测试4相步进电机常规驱动 2、需要用跳帽或者杜邦线把信号输出端和对应的步进电机信号输入端连接起来 3、速度不可以调节的过快，不然就没有力矩转动了 4、按s4（设置成独立按键模式）可以控制正反转 -Contents: 1, the procedure used to test the four-phase stepper motor-driven two conventional, need to jump cap or the signal output line of DuPont and the corresponding stepper motor signal input terminal connected three speed adjustment can not be too fast, Otherwise, there would be no moment of rotation of the four, according to s4 (set to form an independent key mode) can control the positive inversion

51单片机C语言编程手册，由周立功发布，详细介绍了51的硬件与C编程-51 Single-chip C language programming manual, by the week Ligong released details of 51 hardware and C programming

c51学习使用的资料 有100多个原程序-decoder learning to use the data more than 100 original program

该程序完成eeprom的编程，用于写读和擦除的芯片的操作。-Completion of the program EEPROM programming, for writing and reading the chip erase operation.

本程序用于MICROCHIP 24LC64 EEPROM的读写。本程序不使用芯片级联方式， 请将A0，A1，A2 管脚接至低电平。本程序使用IOC6作为SDA，IOC7作为SCL。 程序中的地址空间最大可至64K：24LC00-16-0，24LC01-128-8，24LC02-256-8， 24LC04-512-16，24LC08-1K-16，24LC16-2K-32，24LC32-4K-32，24LC64-8K-32， 24LC128-16K-64，24LC256-32K-64，24LC512-64K-128，读写数据均为8bits。 以上器件的格式为（型号-地址空间-页大小）不同器件的页大小不同，因此页写 程序需作相应修改，其他字节写，随机读以及顺序读程序均相同-This procedure for the MICROCHIP 24LC64 EEPROM read and write. This procedure does not use chips cascade way, please A0, A1, A2 pin to low level access. This procedure used IOC6 as SDA, IOC7 as SCL. Process address space available to the largest 64K: 24LC00-16-0, 24LC01-128-8, 24LC02-256-8, 24LC04-512-16, 24LC08-1K-16, 24LC16-2K-32, 24LC32-4K- 32,24 LC64-8K-32, 24LC128-16K-64, 24LC256-32K-64, 24LC512-64K-128, read and write data are 8bits. The format for the above device (Model- address space- page size) of different devices of different sizes of pages, so page written procedures need to be amended accordingly, and other bytes to write, rand