uIP运行于8位

凌阳最出的超声波测距模组，通过555产生40KHz的超声波，有SPE061A单片机控制超声波的发射和接收，最初的版本在程序方面比第二版本来得简单，主要是通过了硬件电路减少了程序，附电路图、PCB图等-Sunplus most of the ultrasonic ranging modules, 40KHz generated through 555 of the ultrasound, ultrasound has SPE061A single-chip microcomputer to control the transmitting and receiving an initial version of the procedure than the second version is more simple, mainly through the reduction of hardware circuit procedures, with schematics, PCB map

这是f040与2401连接后，进行通信的程序。已经调试通过了 仅供大家参考 第一次传 不好的习惯请大家指正 -This is connected with the 2401, the communications procedures. Debugging has been adopted only refer to the first-bad habit of correcting Thank you, please

ST736单片机，驱动液晶芯片HT1623-ST736 MCU, LCD driver chip HT1623

三相步进电机的三相六拍工作方式，正转的绕组通电顺序：A、AB、B、BC、C、CA、A，反转的通电顺序：A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性，故步进电机的工作过程中不能及时的启动和停止，在启动时应慢慢的加速到预定速度，在停止前应逐渐减速到停止，否则，将产生失步现象。 步进电机的控制问题可总结为两点： 1、产生工作方式需要的时序脉冲； 2、控制步进电机的速度，使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.

使用IA4421模块来进行无线收发，单片机连接。分别收发-IA4421 module using a wireless transceiver, microcontroller. Sending and receiving, respectively

单片机交通灯等课程的程序原代码。 看到有人求这个，特地传上来。-SCM traffic lights curriculum program source code. See people for this, specifically- onto.

超精简的读写u盘程序，只有180行，可生成文件系统，估计再没有比这更短的程序了把？-Super-streamlined procedures to read and write u disk, only 180 lines, can generate the file system, it is estimated that more There is nothing short of the procedures?

ARM 44b0x的PWM完整源代码,并且已经调试通过-ARM 44b0x PWM complete source code, and debugging has been adopted

单片机键盘MakeKey编程-microcontroller programming keyboard MakeKey

pic876采集车轮信号，陀螺仪信号和里程信号，计算出当前的位置，在mpmab上能正确运行。-pic876 wheels signal acquisition, gyroscope signal and signal mileage calculate the current position in mpmab can function correctly.