arm7 lpc2132 GPIO driver for beep

avr单片机atmea16程序。实现发光二极管1s频率闪烁-avr microcontroller atmea16 program. Frequency of blinking light-emitting diodes to achieve 1s

单片机atmega16内部模数转换程序，功能：通过调节ADC0、ADC1两个电位器来改变输入电压，并在数码管同时显示两路电压值。-SCM atmega16 internal analog-digital conversion procedure, function: by adjusting the ADC0, ADC1 two potentiometers to change the input voltage, and also showed two-way digital control voltage value.

我自己写的一个tcp/ip的代码，很短，用的是vc来做模拟调试的，具体的运行是要在mcs51单片机上的，只有一个端口。具体请大家看程序吧！-I wrote it myself a tcp/ip code, in a very short, it was vc do simulation testing, the specific operation is to mcs51 MCU, only one port. Please refer to specific procedures!

单片机C语言实现的对芯片25045的读写操作的语言的源代码。可供单片机开发人员参考。-SCM C language for the 25045 chip and write the language of the source code. SCM developed for reference.

与单片机通信,实现多功能控制界面,内容详细,涉及多个方面-With the single-chip communication, the realization of multi-function control interface and detailed, involving many aspects

AVR单片机，mega16开发板，驱动1602液晶显示程序。-AVR single-chip, mega16 development board, the procedure-driven liquid crystal display 1602.

51的GPIO模拟iic的驱动程序，用宏来定义硬件管脚，容易移植，keil平台-51 GPIO IIC driver simulation, using macros to define the hardware pin, easy to transplant, keil platform

LCD12864的ASCII字库，相关的LCD驱动可以在我发布的其它驱动中找到。-LCD12864 of the ASCII character, the relevant LCD driver can be the other driver I have found.

三相步进电机的三相六拍工作方式，正转的绕组通电顺序：A、AB、B、BC、C、CA、A，反转的通电顺序：A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性，故步进电机的工作过程中不能及时的启动和停止，在启动时应慢慢的加速到预定速度，在停止前应逐渐减速到停止，否则，将产生失步现象。 步进电机的控制问题可总结为两点： 1、产生工作方式需要的时序脉冲； 2、控制步进电机的速度，使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.

AVR MEGA162开发摩托罗拉产GPS模块FCOnOre,价格比较低廉，性能好，但需要进行初始化后才能工作，代码功能是初始化模块及接收GPS信息，也包括部分的SPI双机通信-The development of AVR MEGA162 Motorola GPS module production FCOnOre, relatively low price, performance good, but it needs to initialize in order to work, the code function is to initialize the module and receive GPS information, but also part of the SPI double machine communication