登录
首页 » Matlab » 航天器最优控制算例

航天器最优控制算例

于 2022-01-30 发布 文件大小:3.80 kB
0 109
下载积分: 2 下载次数: 4

代码说明:

航天器最优控制算例,导弹末制导线性二次型最优制导律设计与仿真,通过具体事例,加深对最优控制理论的理解, 尤其是最优控制的初始化条件和性能指标

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • MMA_64
    MMA盲均衡算法,上传供交流,希望大家提供宝贵的意见(MMA blind equalization algorithm, uploads for the exchange, we hope to provide valuable advice)
    2007-01-07 14:43:06下载
    积分:1
  • control
    p pi and pid control which is very important to control strategy .
    2014-10-19 09:54:01下载
    积分:1
  • BEP
    Bit Error probability for different modulation schemes
    2009-09-29 03:00:44下载
    积分:1
  • visionLab4
    code for vision stuff homework related
    2009-11-01 09:16:14下载
    积分:1
  • chengxu
    小波变换进行变速箱故障诊断 首先将s1和s2信号时域谱(s1代表维修前的振动信号,s2代表维修后的振动信号),画出来进行对比,会发现s1信号的振动幅值会比较高;然后对s1和s2分别进行小波分解并画出各层的时域谱,只对比s1和s2分后的最高时域谱,s2更加的具有周期性,且幅值较小,s2周期性不够明显,且振动过于密集。分析完时域谱后开始分析频谱,首先对原信号s1和s2fft转换,得到频谱图,如图,然后再对小波分析后高频部分进行fft转换,做出频谱图。对比后我们发现,在f 2375HZ出(也就是齿轮的啮合频率),s1信号频谱幅值会有急剧的升高,然后,其谐波的幅值也会增大。所以可以推断出该维修前的增速箱的齿轮可能出现问题。(Gearbox fault diagnosis based on wavelet transform s1 and s2 first time domain signal spectrum (s1 behalf of the vibration signal before maintenance, vibration signal s2 representative of repaired), drawn comparison, you will find a signal s1 vibration amplitude will be higher then s1 and s2 respectively wavelet decomposition and draw the layers of time-domain spectrum to only a maximum time domain spectroscopy s1 and s2 points after, s2 is more cyclical and smaller magnitude, s2 cyclical enough obviously, and the vibration is too dense. End domain spectral analysis after the beginning of the spectrum analysis, the first of the original signal s1 and s2fft conversion to give the spectrum, as shown, and then after the high frequency part of wavelet analysis fft transformation to make spectrum. We found that after the comparison, at f 2375HZ out (i.e. the gear mesh frequency), there will be a sharp increase in the amplitude spectrum of the signal s1, and then, the amplitude of the ha)
    2017-01-17 19:18:02下载
    积分:1
  • 四叉树分割
    资源描述下面这段程序演示了在MATLAB中对图像进行基于四叉树的区域分割方法,四叉树就是将一幅图像分成四个区域,将这四个区域的每个区域再次分成四个区域,并如此不断的继续下去。用到了qtdecomp()、qtgetblk()、qtsetblk()函数,可供读者参考学习。希望对读者有所帮助!
    2022-01-24 09:26:18下载
    积分:1
  • 推荐下载OFDM系统中的资源调度算法应用程序
    一个很有用的程序,供做算法研究人员参考,GPS和INS组合导航程序,有CDF三角函数曲线/三维曲线图,Relief计算分类权重,Matlab实现界面友好。
    2022-11-20 00:40:02下载
    积分:1
  • rttarduinouno
    model Simulink of arduino
    2014-01-04 05:06:22下载
    积分:1
  • ofdm_16qam
    16QAM调制OFDM系统仿真示例,实现OFDM系统各部分的基本功能(16QAM modulation OFDM system simulation example, the realization of OFDM system basic functions of each part)
    2013-05-22 18:00:12下载
    积分:1
  • 测试过的MFCC参数的提取matlab源程序
    用于特征降维,特征融合,相关分析等,实现了对10个数字音的识别程序是小学期课程设计的题目,基于kaiser窗的双谱线插值FFT谐波分析,有井曲线作为输入可计算其地震波的衰减,考虑雨衰 阴影 和多径影响。
    2022-01-29 03:16:07下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载