flashflex51单片机

ARM9芯片片外启动的初始化以及中断处理程序-ARM9 chip, chip to start the initialization and interrupt handler

Atmel Uart C51程序（timer1方式）-Uart (timer1 way)

关于传感器的程序，请各位大侠给予指导，等-Procedures on the sensor, please heroes for guidance, etc.

FlashAcessV0.4.6版，用于烧写FALSH的应用程序，需要BANYAN DAEMON的支持，配合BNAYAN系列仿真器或者简易JTAG电缆访问目标板上的FLASH，可支持ARM7/ARM9，各种FLASH。需要1K RAM 运行-FlashAcessV0.4.6 version for the application programmer FALSH, BANYAN DAEMON need the support and facilitation of BNAYAN series or simple JTAG emulator target cable access board FLASH, can support ARM7/ARM9, a variety of FLASH. 1K RAM needs to run

C8051FXXX单片机串口初始化程序，采用c语言编写-Single-chip serial C8051FXXX initialization procedure for the preparation of c language

AVR官方设计的充电器,为SLA、NiCd、NiMH和Li-Ion电池设计的充电器。-AVR official charger designed for SLA, NiCd, NiMH and Li-Ion battery charger designed.

单片机RS232/RS485串行发送实验（双机通讯）。 实验步骤： （1），准备两台598K实验机，确定1号机为发送，2号机为接收； （2），当作RS232接口实验时，1号机和2号机的P3.0和P3.1交叉相连，且两机共地； （3），当作RS485接口实验时，1号机和2号机的A、B作对应连接，同时1,2号机的R/TEN接P1.0, P3.0接R0, P3.1接DI。 （4），先运行2号机，键入[27]-->[EV]使2号机处于接收状态P。，后运行1号机[26]-->[EV]使1号机处于发送状态,P。会闪烁，在1号机键盘上按动数字键，在2号机的数码管上应显示对应的数字键值。-Send Singlechip RS232/RS485 serial experiment (two-plane communications). Experimental steps: (1), prepare two sets of experiments 598K machine, determined on the 1st machine to send, on the 2nd machine to receive (2), as a RS232 interface experiment, on the 1st and the 2nd machine and P3.0 P3.1 cross-linked, and the two planes were to (3), as a RS485 interface experiment, on the 1st and the 2nd machine A, B for the corresponding connection, while 1,2 No. of R/TEN then P1 .0, P3.0 access R0, P3.1 then DI. (4), first run on the 2nd machine, type [27]

单片机开发, 单片机开发-MCU Development, microcontroller development, the development of microcontroller, microprocessor development, the development of SCM

enc28j60的驱动， 通过ping命令来测试enc28j60是否连同 -enc28j60 drive through ping command to test whether or not together with enc28j60

1.Ｋ１作为左转弯开关，Ｋ２作为右转弯开关。Ｌ１、Ｌ２作为左转弯灯，Ｌ５、Ｌ６作为右转弯灯。 2.程序实现的功能：向上打Ｋ１时左转弯灯以一定频率闪烁，打Ｋ２时右转弯灯以一定频率闪烁，Ｋ１、Ｋ２同时向上或向下，发光二极管灭。-1.K1 as a left turn switch, K2 as a switch and turn right. L1, L2 as a left turn lights, L5, L6 as lights and turn right. 2. Program features: K1 when the left turn up to fight a certain frequency of flashing lights, turn right when playing K2 to a certain frequency of flashing lights, K1, K2 upward or downward at the same time, anti-light-emitting diodes.