四通道的AD采样转换数据，并用于键盘和数码管的操作和显示。附有参考资料和pdf格式的原理图。...

利用DS18B20采集温度，显示温度到lcd上-DS18B20 collected using temperature, shows that the temperature on the lcd

用ansi c 实现针对时钟芯片HT1380的驱动程序，以及实现电子时钟的源码-with ansi c achieve against the clock chip HT1380 driver, and the realization of the electronic clock source

电机测速源码程序，好使的已经通过测试了。非常精确-Motor Speed-source program, so that has passed the test. Very precise

此文件是在ＤＯＳ环境下对交通信号灯进行的设计，完成了红黄绿灯的相互转换．-this document is in the DOS environment for the traffic signal design, the red and yellow green to complete the conversion.

ADI公司ADuC841单片机源程序。 I2C.c: ADuC841单片机I2C接口函数。 kei841.h： ADuC841单片机内部寄存器定义。 delay.c：精确延时资函数。 main_new.c ADuC841单片机主函数，实现正弦波的输出和I2C接口LED显示-ADI ADuC841 MCU source. I2C.c : ADuC841 MCU I2C interface function. Kei841.h : ADuC841 MCU internal register definitions. Delay.c : precision-delay function. Main_new.c ADuC841 MCU main function, achieve sine wave output interface and I2C LED Display

AD7705是16位模数转换器件 此程序为其驱动程序-AD7705 ADC is 16 pieces of this program for its drivers

WAVE6000编写的常用的程序 包括键盘 通信 数据转换 -WAVE6000 prepared by the common keyboard communication procedures include data conversion

拷拷贝到你的Keil安装目录下的c51in文件夹中。 工程文件中需设置一下: project->Option for Target Target1 选Debug页 左侧最下面 Dialog Dll 一般是DP51.DLL，不用修改 Parameter 中是 -P51 在其后加入 -dledkey 即该行看起来应该是这样的： -p51 -dledkey 保存即可 进入调试后，点击：Peripherals，其中多出一个“键盘LED实验仿真板”选择该项即可。-emboss your copy of the Keil installation directory under the decoder bin folder. The project document to be provided as follows : project-gt; Option for Target Target1 election Debug bottom of the left page is generally Dialog Dll DP51.DLL, need not be amended Parameter is- P51 add after-dledkey that the bank should look like this :-p51-can be preserved into dledkey to debug and click : Peripherals, in which more than a "keyboard LED simulation board," which can be chosen.

上载/下载日志 实现小车的自动寻迹小车,且速度较快并且很稳定 2. XUNJI.C.rar,1KB,下载 3 次,小车的寻迹程序,根据车两边的灯的亮灭判断来执行电机的动作 3. Programm.zip,23KB,下载 6 次,控制智能车寻黑线运动,可以转向和前进,能够采集前方信息... www.programsalon.com/upload_log.asp?e=ani ... 5K 2008-9-30 - 百度快照 -Upload/download log to achieve automatic tracing trolley car, and faster and very stable 2. XUNJI.C.rar, 1KB, downloaded 3 times, the car tracing procedures, in accordance with cars on both sides of the bright lights to carry out to determine motor movements 3. Programm.zip, 23KB, downloaded 6 times, control the smart car look black line movement, can shift and move forward to collect the information in front of ... www.programsalon.com/upload_log.asp?e=ani .. . 5K 2008-9-30- Baidu Snapshot

此源码利用单片机模拟实现IIC总线通信，可以连接基于I2C的硬件调试 -use of this source SCM simulation IIC bus communication, based on the I2C can be connected to the hardware debugging