Driver t6963 series LCD, can display text and graphics characters

汇编；每隔10ms响铃一下-compilation; Neither about every 10ms

医院管理信息系统 -Hospital Management Information System

《多按键处理程序 》，适用于工控按键处理 -"multi-key handling procedures" applicable to industrial processing keys

反汇编工具borg2.27源码，文件齐全-anti-compilation tools borg2.27 source, the complete document

开发环境：FASM 功能：听过不要音箱的音乐么（当然也包括耳机之类的罗），这就是一个不要音箱也可听的音乐，怎么回事，请看源代码

该程序为VB程序,是用于计算出来的坐标需要进行坐标系转换使用.感谢站长-procedure for the VB program is used to calculate the coordinates of the need for the use of coordinate system conversion. Grateful to the station! !

1. 本程序中，首先应输入一个值赋给初始报数上限m，人数n应为任意的，程序应能自动保存出列人的序号并将出列的人所持的密码赋给m，再次作为报数上限，然后删除出列人信息。如此循环，直至所有人都出列为止。 2. 程序以用户和计算机的对话方式执行，即在计算机屏幕上显示“提示信息”之后，由用户在键盘上输入相应数据（即每个人所持的密码），每个人的序号由程序自动分配并存储。 -1. This process should first enter a value assigned to the initial reported that the maximum number of m, the number n should be arbitrary, the procedure should be able to automatically save a number of people out and held out the password assigned to m again reported as the maximum number, and then delete the information out of people. Such a cycle, until all that far out. 2. Procedures to computer users and the implementation of the dialogue, that is displayed on the screen in the computer " message" after the keyboard by the user in the corresponding input data (that is, each person" s password), each individual" s serial number automatically assigned by the procedures and stored.

,片选接到p1.5 复位端 p1.4 中断端接到 int0 82c250工作在斜率模式下 ，RS 接51k电阻到地。 2，SJA1000与82C250的接口，逻辑上为SJA1000输出0（显性位），表现为低点平输出给82C250，则82C250输出 差分的低电平。SJA1000输出1（隐性位），表现为高电平或悬空输出给82C250，则82C250输出悬空状态。 3,周立功的中SJA_BCANCONF.ASM中对输出控制寄存器 的TX0的输出 极性的位的定义不对。 还有里面定义有接收错误标志码，不知道何时用。-, The election received a P1.5-chip client p1.4 interrupt reset int0 82c250 client received in the slope mode, RS then 51k resistor to ground. 2, SJA1000 with the 82C250 interface, logic for SJA1000 Output 0 (dominant bit), showing low level output to the 82C250, while the low-level differential output 82C250. SJA1000 Output 1 (recessive), and the performance of the output is high or left vacant to the 82C250, the vacant state 82C250 output. 3, Zhou Ligong in the SJA_BCANCONF.ASM of output control register TX0 output polarity bit the definition of wrong. Inside the definition also has to receive error flag code, I do not know when to use.

以MPS430F149为硬件平台，利用I/O口模拟I2C总线协议，对日精的时钟芯片S35390A_C做了初始化子程序、读时钟子程序、写时间子程序、脉冲为1赫兹输出子程序。-To MPS430F149 for the hardware platform, the use of I/O port simulation I2C bus protocol on-chip clock nissei S35390A_C done initialization subroutine, read subroutine clock, the time to write subroutines, pulse for 1 Hz output subroutine.

分区详细资料，8086ASM-through detailed information 8086ASM