eeprom24c02程序代码，经测试可以使用，分享一下

读标准韦根26码的程序，效果不错，只是需要后上电-Reading standard Wiegand 26 yards of the procedure, good results, but needs power

用凌阳单片机开发的迎奥知识问答机器人。 通过语音识别功能。实现全语音操作。 能通过语音操纵它前进，后退，左转，右转，跳舞，并且能进行交互式的知识问答。如果回答错了，机器人将给于正确答案还和一句鼓励的话，如果回答对了机器人将为你跳一段舞，全部答目答完后会给出总成绩。-Single-chip developed by Sunplus Ying Austrian robot quiz. Via voice recognition. Realize full-voice operations. Voice manipulation it can move forward and backward, turn left, turn right, dancing, and can be interactive quiz. If the answer is wrong, the robot will be in the correct answer and also an encouragement, and if the answer to will you jump for some robot dance, all the heads at the end of A will give a total score.

采用8位LED动态扫描时钟演示程序 使用12MHZ晶振，P0口输出段码，P2口作列扫描，用共阳LED数码管-Using 8-bit LED Dynamic scan demo program using the 12Mhz clock crystal, P0 port output above code, P2 I make out scanning, with a total of Yang LED digital tube

利用SPCE061A实现中文输入,必要时可适当删减-use SPCE061A achieve input and, if necessary, can be properly cut

详细介绍了单片机的总线设计法，讲述清除并有设计实例-Details of the MCU bus design method, and a design example about the removal

C51七种实用子程序集3-C51 seven practical subroutine Set 3

描述msp430的端口控制以及频率设定 的一个简单程序

STM32 FSMC 驱动TFT LCD-STM32 FSMC drive TFT LCD

avr Led test program in c

三相步进电机的三相六拍工作方式，正转的绕组通电顺序：A、AB、B、BC、C、CA、A，反转的通电顺序：A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性，故步进电机的工作过程中不能及时的启动和停止，在启动时应慢慢的加速到预定速度，在停止前应逐渐减速到停止，否则，将产生失步现象。 步进电机的控制问题可总结为两点： 1、产生工作方式需要的时序脉冲； 2、控制步进电机的速度，使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.