C51单片机与nrf2401使用，nrf2401调试程序。

本综合项目设计电子图书、数码相框、音乐播放、应用中心、时钟、系统设置、FC 游戏机、收音机、记事本、运行器、 3D、手写画笔、照相机、录音机、 USB 连接、 TOM 猫、无线传书、计算器。

资源描述本程序是基于STM32 F103的程序，模拟示波器，可以在上面显示所采集的数据，可以方便供stm32的初学者，起到借鉴的作用。程序的算法比较简单易懂。 

NEC格式遥控接收代码：NEC IR implementation -NEC form remote control receive code: NEC IR implementation

LPC2131开发板第4章－LPC2131功能部件4.1－GPIO3．GPIO输出实验－流水灯实验GPIO_Leds8-2.rar-LPC2131 Development Board Chapter 4-LPC2131 features .1-GPIO. GPIO output experiment- light water experiment GPIO_Leds8-2.rar

单片机贪吃蛇游戏,可在89c51等单片机运行. keil编译-SCM Snake game, you can 89c51 microcontroller such as running. Keil compiler

51 红外发送程序 带仿真 数据格式可以修改程序来实现-51 infrared send process with simulation data formats can modify the procedure to realize

通过使用ＺＬＧ／ＣＦ驱动读写ＣＦ卡或ＩＤＥ硬盘的指定扇区等操作实验，掌握ＺＬＧ／ＣＦ驱动的使用。-Through the use of ZLG/CF drive to read and write CF card or IDE hard drive designated sector operations such as experimental, master ZLG/CF drive use.

用LPC2136测试三维加速度传感器mma7456,用模拟I2C实现通信-Three-dimensional acceleration sensor with the LPC2136 test mma7456, simulated I2C for communication

MCB517 I2C源碼。，用於Freescale芯片系列；供需要研究I2c或iic源代碼的同好參考。當初的取得來源已經忘了。This file contains example code to print over the serial  port of the MCB517 MCU and Evaultion Board (EVAL-MCB517QS).    This example will test the I2C function of the MCB517.    This will be done by writing and reading from    a serial A/D & D/A (P8591).     This example will bit bang two general I/O ports for I2C   The example work with communicate at: 9600, 8, N, 1.    This code was tested using the mon-51 connected through COM-1    of the eval board.    CPU Frequency: 11.0592 MHz 

开发环境:ADS 1.2/SDT 2.51 GUI测试，由于没有触摸屏，所以将触摸屏的代码给屏蔽了； 请将FS44B0II开发板连接好交叉网线、直连串口线、电源， 并连接好G57液晶屏，同时还要连接好背光电源； 然后在BIOS的命令窗口里面敲netrun命令； 点击FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel目录下： 批处理文件FS44B0_G57_uCGUI.BAT 下面你就可以看到液晶屏上面显示优龙标志 它会延时一两秒中进入下一个画面，逐步延时GUI的各项功能，请耐心观看； -Development Environment: ADS 1.2/SDT 2.51GUI test, because there is no touch screen, it will be touch screen to shield the code Please FS44B0II development board to connect a good cross-network lines, direct serial lines, power supply, and connect a good G57 LCD screen, at the same time, good backlight power supply connection and then in the BIOS command window knock netrun order Click FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel directory: batch file FS44B0_G57_uCGUI.BAT below you can see the LCD screen above shows excellent signs that it will delay Liuzhou 1 two seconds to enter the next screen, and gradually delay the GUI features, please be patient watch