这个程序利用89S51演奏生日快乐的歌曲 */

共搜集了13个有关51单片机的一些基本程序，代码有汇编写成，内容包括计数器、温度检测等等。-collected a total of 13 of the 51 SCM some of the basic procedures, a compilation of code written, including counter, temperature measurement, and so on.

CH341评估板，演示USB转串口、转打印口、转并口及同步串口等-CH341 Evaluation and demonstration USB to serial, LPT switch, switch synchronous serial port and parallel port, etc.

控制步进电机正转，如：p3.2正转,p3.3反转,p3.4停止 步进电机接p1.0p1.1p1.2p1.3，正转，反转各3圈，正反快慢功能，是步进机的经典程序。-Stepper motor control is transferred, such as: p3.2 is transferred, p3.3 inversion, p3.4 stop stepper motor then p1.0p1.1p1.2p1.3, is turn, reversal of the 3 lap, both positive and negative speed function, is a classic step process machine.

SST89C58的IAP功能进行在线下载程序的步骤-SST89C58 the IAP function for online download steps

PIC单片机驱动ADC9850程序，采用并口方式，输出为正弦波-PIC MCU driver ADC9850 procedure for the parallel mode, the output of sine wave

】本文介绍了一个使用单片机和CPLD联合控制步进电机的方案。首先阐明步进电机的工作原理及控制方法，然后 提出了系统的软硬件设计框架，详细讨论了单片机和CPLD的逻辑接口问题和交换数据的协议，以及用状态机来设计脉冲分配器 的方法。-This paper describes a combined use of SCM and CPLD stepper motor control program. First of all, to clarify the working principle of stepper motor and control method, and then put forward a system of hardware and software design framework for a detailed discussion of the MCU and CPLD logic interface issues and data exchange agreements, as well as the use of state machine design Pulse Distributor methods.

用485实现单片机之间的串行通信。 从机部分一直等待主机的命令，接收到就发响应信号，然后接受数据，接受成功就用液晶显示-MCU with 485 Serial Communication between. From the plane of the mainframe have been waiting for the orders received on the response signal and then receive data on the successful use of acceptable LCD

HT24 系列的EEPROM 总共8 个管脚，三个为芯片地址脚A0、A1、A2，在单片机对它进行操作时，从SDA 输入A0、A1、A2 数据和芯片外部A0、A1、A2 所接地址需一一对应。一个为芯片写保护脚WP，WP 脚接低电平时，芯片可进行读写操作；WP 脚接高时，芯片只可进行读，不可进行写。 另外两个管脚为电源脚VCC，VSS。 用单片机对HT24 系列的EEPROM 进行控制时，HT24 系列的EEPROM 的外部管脚VCC、VSS、WP、A0、A1、A2 根据需要，对应接上，SDA、SCL 接到单片机控制脚上。-HT24 Series EEPROM total of 8 pins, three pins for the chip address A0, A1, A2, in the microcontroller to operate it, from SDA input A0, A1, A2, and chip external data A0, A1, A2 of the Then one correspondence address must be in. One for the chip, write-protect pin WP, WP feet then low, the chip can be read and write operations WP pin is high then, the chip can only be read, not write. The other two pins for the power pin VCC, VSS. With the microcontroller on the HT24 Series EEPROM control when, HT24 Series EEPROM external pin VCC, VSS, WP, A0, A1, A2 according to the needs of the corresponding connected, SDA, SCL receives SCM control feet .

12864液晶画图原C代码

主要用到了PID算法控制温度,显示采用动态扫描.输出可调节占空比的脉冲控制加热器-mainly used to control the temperature PID algorithm, shows that using dynamic scanning. Output adjustable pulse duty cycle control of the heater