LCD12864的ASCII字库，相关的LCD驱动可以在我发布的其它驱动中找到。...

系统can地址为550,用于can系统测试,应用T0定时器每隔1s向can总线发送一组数据:数据长度为8个字节, 首字节为05H,第二个字节为累加变量,每秒钟数值增加1,-system can address 550 for the test system can, Application T0 1s to every timer can send a bus of data : data length of 8 bytes the first byte of 05H, the second byte of cumulative variable, an increase in value per second.

用AVR单片机实现的乐曲编码程序，使用C语言写的-with AVR MCU music coding procedures, the use of the C language to write

欧几里德算法：辗转求余　　原理: gcd(a,b)=gcd(b,a mod b)　　当b为0时,两数的最大公约数即为a　　getchar()会接受前一个scanf的回车符-Euclidean algorithm: Principles of travel for more than: gcd (a, b) = gcd (b, a mod b) when b is 0, the two common denominator is the number of a getchar () will accept the previous scanf carriage return

针对NEC系列单片机的初始化程序,如需详细,请邮件联系-For NEC MCU initialization procedure, For more details, please e-mail contact

tc35应用C程序 短息发送、接受（单片机控制）-tc35 application C program

自己写的 STM32 串口UART驱动, 不用固件库。超级终端界面按键时,自动回送。 应用范围: 因为不涉及IO口,所以此工程在STM32F1xx的任何主板上都可以运行。 编译器: IAR ARM 4.42A。 作者: w123456xy@sohu.com 15189792379。 -Write your own STM32 serial UART driver, no firmware library. HyperTerminal interface button, automatically send back. Application scope: because they do not involve IO port, so this works on any STM32F1xx motherboard can run. Compiler: IAR ARM 4.42A. Author: w123456xy@sohu.com 15189792379.

红外线遥控器按键检测程序. 通过检测两次下降沿之间的时间差判断接受到的数据位. 已经通过了测试,能够正确区分出32bit数据的遥控器按键键值. 具有数据重发功能,但是数据的重发有点频繁. 使用晶震频率为11.0592MHz,所有定时值都是基于这个频率计算. 占用很少量的CPU时间,使用了外部中断0接受数据,定时器0进行计数, 定时器1作为串口的波特率发生器(Band = 9600).-Infra-red remote control button detection program. By detecting falling edge twice to determine the time difference between the received data bit. Has passed the test, could correctly distinguish 32bit data button remote control key. With data re-issued, but data a bit of re-issued frequent. Zhenyuan frequency of use of crystal 11.0592MHz, all timing values are calculated based on this frequency. occupied by small quantities of CPU time, use the external interrupt 0 to accept data, timer 0 to count, timer 1 as a string port baud rate generator (Band = 9600).

315M无线遥控解码程序,最大的问题就是距离，现在只能在100m左右。-315M wireless remote control decoding procedure, the biggest problem is the distance, now only about 100m.

我用单片机8952和电压比较器339做了一个简单的电容容量测量表，参数大 致如下： 电容测量范围为1pF-9999.99uF，最小分辨力为1pF。分为5个量程，可以自 动切换量程，也可手动切换。 另外，有简单的频率计功能，能测量0-60MHz的数字信号频率（TTL电平）； 还可以产生几个单点频率的方波信号（比如1KHz）。 采用1602LCD作为显示器；4个按键控制；使用24C01保存当前设置值，不用 每次开机重新设置。可单5V供电，也可9V交流供电 -I used the single-chip 8952 and the voltage comparator 339 to do a simple capacitance measurement table, parameters are as follows: capacitance measurement range 1pF-9999.99uF, the minimum resolution for the 1pF. Divided into five ranges, you can automatically switch range can also be manually switched. In addition, a simple frequency meter function, capable of measuring 0-60MHz frequency digital signal (TTL level) can also lead to several single-point-frequency square-wave signal (for example, 1KHz). 1602LCD used as a monitor 4 button control use 24C01 to preserve the current settings, do not reset each boot. Can be a single 5V power supply, 9V AC power supply can also be

74ls165控制扫描键盘，串行输出键值的c51键盘程序，并在led上显示-74ls165 control scanning keyboard, serial output of the decoder keyboard keys procedures, and led the show