此程序时周立功ZLG7290源码驱动，这是我开发版上的源码

PHILIPS的PCA捕捉功能和高速输出功能-PHILIPS features of the PCA to capture and high-speed output function

Keil C51 上51系列单片机优化的CRC－8 算法。可以自己改其他算式的，包含字节查表，半字节查表，bit计算。很难得的哦。-Keil C51 on the 51 computers optimized CRC-8 algorithm. Other formula can do it ourselves, and look-up table contains the byte, half-byte look-up table, bit computing. Hard to come by Oh.

自制的串口控制8路光藕隔离输出，可以通过计算机串口控制，8路输出-homemade serial control a variety of eight-channel optical output isolation can be controlled via computer serial port, eight output

基于AVR单片机的串转并大屏幕汉字显示 开发环境 I-Based on the AVR MCU series and big screen to show the development environment of Chinese Characters I

非常好的AVR单片机常见问题问答,对于开发人员适用. -Very good AVR Singlechip frequently asked questions, for the application developers.

一个单片机对EEPROM AT24C02的读写程序。绝对好用。-A single-chip EEPROM AT24C02 on reading and writing process. Absolute ease of use.

HT24 系列的EEPROM 总共8 个管脚，三个为芯片地址脚A0、A1、A2，在单片机对它进行操作时，从SDA 输入A0、A1、A2 数据和芯片外部A0、A1、A2 所接地址需一一对应。一个为芯片写保护脚WP，WP 脚接低电平时，芯片可进行读写操作；WP 脚接高时，芯片只可进行读，不可进行写。 另外两个管脚为电源脚VCC，VSS。 用单片机对HT24 系列的EEPROM 进行控制时，HT24 系列的EEPROM 的外部管脚VCC、VSS、WP、A0、A1、A2 根据需要，对应接上，SDA、SCL 接到单片机控制脚上。-HT24 Series EEPROM total of 8 pins, three pins for the chip address A0, A1, A2, in the microcontroller to operate it, from SDA input A0, A1, A2, and chip external data A0, A1, A2 of the Then one correspondence address must be in. One for the chip, write-protect pin WP, WP feet then low, the chip can be read and write operations WP pin is high then, the chip can only be read, not write. The other two pins for the power pin VCC, VSS. With the microcontroller on the HT24 Series EEPROM control when, HT24 Series EEPROM external pin VCC, VSS, WP, A0, A1, A2 according to the needs of the corresponding connected, SDA, SCL receives SCM control feet .

PIC单片机驱动ADC9850程序，采用并口方式，输出为正弦波-PIC MCU driver ADC9850 procedure for the parallel mode, the output of sine wave

AVR单片机16位CRC校验码生成及CRC校验子程序-AVR 16 CRC generation and CRC Subroutine

用8051驱动240*128液晶的C51程序，控制器为T6963，由于代码比较大，试验时请用52 本程序移植性较好，已成功移植到MSP430上-8051 with 240* 128 LCD drive the C51 procedure, the controller for the T6963, as a result of relatively large code, test when you use 52 transplant procedures better, have been successfully transplanted into MSP430 on