51定时器中断例程，比较经典的实际使用定时器的说明

这是mcs-51和EEPROM AT24C512 I2C总线接口器件接口的例子 -This is a mcs-51 and EEPROM AT24C512 I2C bus interface device interface example

T6963C的控制及初始化指令，包含一个简单字符显示-T6963 control and initialization scripts, including a simple character display

The sample software includes, common library, peripheral APIs, and test modules for the APIs. The common library include startup file, standard definition and header files, processor specific setup module, generic interrupt related APIs, timer routine, and scatter loading file. The peripheral directories include, GPIO, PWM, Real-time clock, timer, SPI, I2C, Watchdog timer, UART, external interrupt, etc.

显示： “欢迎使用"， "单片机实验系统" lcd显示汉字-shows : "Welcome," "SCM experimental system" LCD display Chinese characters

本程序给出了一种msp430单片机模拟实现i2c总线的一种方法-this procedure gives a MCU Controller Simulation i2c a method Bus

DESCRIPTION =========== This example project shows how to use the IAR Embedded Workbench for ARM to develop code for the Atmel AT91SAM9261 evaluation boards. It shows basic use of parallel I/O, timer and the interrupt controller. It starts by showing different patterns on the LED s separated by half second. COMPATIBILITY ============= The project is compatible with the AT91SAM9261-EK board.

* 硬件结构： PA0-5对应６个ＬＥＤ数显管的位 ，PC0-7对应各ＬＥＤ数显管的段 ，PB4-7为键盘。 * 软件描述： 上电后，时钟从00.00.00（时/分/秒）自动走时，在走时状态时 ， 按PB4（设定 * 键）超过3秒可循环选择调整时间/工作参数 ，接着按PB5以确定选择的操作 ，进入调整操作后 ， * 按PB5选择欲调整参数，按PB6（增加键）完成调整参数操作 。按PB7，进入时控运行，PB1亮， * 再按PB7停止时控运行，回显走时。在定时到时，PB0点亮。- * Hardware architecture: PA0-5 corresponds 6 LED numbers to reveal the tube the position, PC0-7 corresponds each LED number to reveal the tube the section, PB4-7 is a keyboard. * Software description: After on electricity, clock from 00.00.00 (when/a minute/second) is in luck automatically, when is in luck the condition, according to PB4 (hypothesis * The key) surpasses for 3 seconds to be possible to circulate the choice time/operational parameter, then presses PB5 by to determine the choice the operation, after enters the adjustment operation * Wants according to the PB5 choice to adjust the parameter, (increases key) according to PB6 to complete the adjustment parameter operation.According to PB7, enters when controls the mov

用89S52编的的蜂鸣器发声，有点简单，但最为一个发声的实力来说足够了-89S52 series with the buzzer sound, a bit simple, but most of the strength of a voice enough for the

数码管的显示操作，同时也有按键操作程序，通过单片机控制可以直接进行显示-Digital tube display operation, but also has key operating procedures, can be directly controlled through the single-chip display

LPC915的I2C模块配置为从机时的接口程序 可直接添加到工程里使用-LPC915 I2C module configuration from the plane at the interface can be directly added to the used in the project