这是一个IC卡智能水表程序,我已编译过可以用的.

这个范例说明如何使用8051 的Port 1连接LCD显示器，PORT 3.3、P3.4和P3.5则连接到LCD显示器的控制线。程序执行时将显示出Hello Keil C和LCD display */-This example shows how to use the 8051 Port 1 to connect LCD displays, PORT 3.3, P3.4 and P3.5 are connected to the LCD display control lines. Program execution will show Hello Keil C, and LCD display* /

该源码采用标准c编写，使用SPI方式访问SD卡。-c prepared using standard, the use of SPI mode visit the SD Card.

51单片机控制TC35I无线通信模块的完整Keil C程序，还包含GB2312与Unicode转换，国标汉字、ASC字符显示，串口通信，液晶模块控制等程序。-51 single-chip wireless communication module TC35i control the integrity of Keil C procedures, also includes GB2312 and Unicode conversion, GB characters, ASC characters display, serial communications, LCD module control procedures.

用一片ARM芯片，对电网中的谐波信号进行采集，然后通过GPRS发送给上位机，上位机对采集到的电网中的谐波信号进行分析。以确定电网中谐波的情况。-With an ARM chip, the harmonics of the grid signal acquisition, and then sent to the GPRS PC, PC to the power grid of the collection of harmonic signal analysis. To determine the grid in the case of harmonic.

触摸屏的校正程序。可以用于触摸屏的校正。在三星的平台上测试通过-Touch screen calibration procedure. Can be used for touch-screen calibration. Samsung

基于PIC16F877A的DS18B20一线总线多路测温系统（采用Proteus模拟）。 Proteus模拟电路图＋PIC C语言源程序（MPLAB V8.00） 这可不是用多I/O模拟的多路测温哦！看系统功能： 1）、由一线数据线寄生供电，采用MOSFET强上拉给DQ供电； 2）、上电自动搜索可用的传感器并做CRC校验（实现了Search ROM命令）； 3）、 报警下限可选择； 4）、轮询显示温度，通过LCD1602输出； 5）、 传感器中途拔出或温度越界均报警； 6）、 采用声光报警方式，可做为温度控制信号标志。 -PIC16F877A-based multi-channel bus of DS18B20 line temperature measurement system (using the Proteus simulation). Proteus analog circuit+ PIC C language source code (MPLAB V8.00) This is not using multiple I/O simulation of multi-channel temperature measurement Oh! See system functions: 1) by the parasitic power line data line, using MOSFET strong pull-up power supply to the DQ 2), power-on automatically search for available sensors and do CRC check (to achieve a Search ROM command) 3) alarm limit choice 4), polling shows the temperature, through the LCD1602 output 5), half-way pulled out or the temperature sensors are all cross-border police 6), using sound and light alarm mode can be used as the

功能：实现对DS18B20的读取 原理：单总线协议 注意：单总线协议对延时要求比较严格，此程序中采用的是11.0592M的晶振，如果使用其他的晶振请跟据DS18B20的资料修改延时参数-functions : to achieve DS18B20 read Principle : single-bus protocol attention : single-bus protocol to delay requirements more stringent, this procedure is used in the crystal 11.0592M if the use of other crystal please According to the information DS18B20 delay parameter changes

包含protue 7.2 仿真文件及汇编语言源代码。主要是一个4X4的键盘以及一个LCD显示显示屏。键盘输入显示在LCD上。-Simulation protue 7.2 contains documents and assembly language source code. 4X4 is primarily a keyboard and a LCD display screen. Keyboard displayed on the LCD on.

自己设计编写18B20温度采集程序，已通过验证。-18B20 prepare their own design temperature acquisition procedures have been validated.

c8051f020读/写LM92并将温度值显示在SAA1064驱动的四位数码管上-C8051F020 read/write and LM92 temperature value displayed on the SAA1064 driver four digital tube