介绍了液晶显示模块基本原理及其技术特性，与单片机的进行接口的具体电路，同时给出了其编程方法和程序代码．...

电机控制的资料下载自 TI 网站 英文版的谁能翻译玩就翻译去吧

基于AT89S52的温度传感器18b20控制系统程序：温度检测，自动转换led显示；具有超限报警功能。-AT89S52-based control system for temperature sensor 18b20 process: temperature detection, automatic conversion led display have overrun alarm.

将演示数据先写入24C04芯片内，再将其数据逐个读出送P0口LED显示。-Data will demonstrate the first to write 24C04 chip, and then read out the data sent by P0 I LED display.

多用途的usb调试程序.用vc编写.可通过增加功能,变成自己的软件.-Usb multi-purpose debugger. Using vc prepared. Can increase the functionality into its own software.

软件UART示例 两个完整的例子,一个用PCA为波特率发生器的C语言程序和一个用定时器0为波特率发生器的汇编语言程序. 适用于下列器件 C8051F000C8051F001C8051F002C8051F005C8051F006C8051F010C8051F011C8051F012C8051F015C8051F016C8051F017C8051F220C8051F221C8051F226C051F230C8051F231C8051F236-Software UART Examples of two complete example, a baud rate generator with PCA for the C language program and a use timer 0 baud rate generator for the assembly language program. C8051F000C8051F001C8051F002C8051F005C8051F006C8051F010C8051F011C8051F012C8051F015C8051F016C8051F017C8051F220C8051F221C8051F226C051F230C8051F231C8051F236 applies to the following devices

单片机操作EEPROM 240X的程序。 非原创，转载。-EEPROM 240X MCU operating procedures. Non-original and reproduced.

AVR单片机入门及C语言高效设计实践（六） ATMEAG16L的定时／计数器 ATMEAG16L有两个8位定时／计数器（T／C0、T，C2）和一个16位定时／计数器T/C1）。每一个计数器都支持PWM（脉冲宽度调制）输出功能。PWM输出在电机控制、开关电源、信号发生等领域有着广泛的应用。[第一段]-AVR C language portal and efficient design practice (6) ATMEAG16L the timer/counter All ATMEAG16L two 8 timer/counter (T/C0, T, C2) and a 16 timer/counter T/C1). Each counter support for a PWM (pulse width modulation) output function. PWM output in motor control, switching power supply, signal and other fields has wide application. [Paragraph]

keil C51 ISR事例-ISR stories

protues 单片机仿真程序音乐播放.包括两只蝴蝶,同一首歌,挥着翅膀的女孩三首歌.可以和keil联机调试.-Single-chip simulation program protues music player. include two butterflies, the same song, waving wings girls 3 song. can keil-line debugging.

状态1：正常时，8个LED发光二极管（彩灯）循环点亮。 • 状态2：有报警时，蜂鸣器发出报警声（用P3.3接一个按键，模拟产生报警信号。当开关合上，发生报警；当开关断开，报警停止。用P3.7输出音频信号驱动扬声器，作为报警信号），同时8个LED发光二极管（彩灯）闪烁。 P3.2接一个按键，用于消除报警-Status 1: normal, eight LED light-emitting diodes (lantern) light cycle.