脑电信号的分析算法的全面概述,包含李氏指数复杂度等

本例载波频率为20KHz，或载波周期为50μs。DSP晶振10MHz，内部4倍频，时钟频率为40MHz，计数周期为25ns。假设调制波频率由外部输入（1～50Hz），并转换成合适的格式（本例为Q4格式）。调制系数M为0～0.9。死区时间1.6μs。最小删除脉宽3μs。 主程序的工作是根据输入的调制波频率计算N、2N和M值。 -Example for the carrier frequency 20KHz, or carrier period is 50μs. DSP crystal 10MHz, internal 4 multiplier, the clock frequency of 40MHz, counting cycle 25ns. Assuming wave frequency modulation by external input (1 ~ 50Hz), and converted into an appropriate format (in this case for Q4 format). Modulation coefficient M is 0 ~ 0.9. Dead time 1.6μs. Delete the smallest pulse width 3μs. The work of the main program is based on input frequency modulation wave calculation of N, 2N and M values.

汇编语言与设计 我们可以这样的做一些有用的汇编程序-assembly language and design we could do some useful compilation proce

0到99秒的计时,误差极小,不同一般的DELAY哦.-0-99 seconds of the time, the error is very small and different from other DELAY oh.

常用EEPROM芯片的读写操作，51单片机控制电路，实验时要用74LS373一片，AT28C16一片，AT28C17一片，电路十分简单，根据实际电路联接情况，自行确定存储地址，最后别忘了还要8个LED和470欧姆电阻.-EEPROM chip used to read and write operations, 51 MCU control circuit, experiment, use 74LS373 1, AT28C16 1, AT28C17 1, the circuit is very simple, based on the actual situation of the circuit connectivity, self-determined memory addresses, finally do not forget to also 8 LED and 470 ohm resistors.

masm在windows环境下运行的安装程序，里面还附有各种命令的帮助等-MASM in the windows environment to run the installation program, which also included the help of a variety of command and so on

用8051单片机实现的有关C 语言简单开发程序-8051 with the realization of the relevant C language to develop simple procedures

液晶显示器LCM320240驱动程序，和触摸驱动程序。-LCM320240 liquid crystal display drivers, and touch driver.

二进制文件比较程序-binary file comparison procedures

P1口的流水灯程序，先亮流水，后不亮流水，正反相对-P1 mouth flow signals procedures and bright water, after failing to turn water, the relative pros and

ST套件产生汽车防盗器报警声,本实例的目的是让大家学会用单片机产生声音的方法，学会计算程序所用时间 本实例的功能是能用16F84产生汽车防盗器的报警声，频率分两个0.1s第一个 0.1S频率从1.8K-3.5K匀速增加第二个0.1S频率从3.5K-1.8K匀速减少, 程序复位后,按S2喇叭叫两声,按S3喇叭叫15秒,中途可按S5停止. PIC单片机 烧写时应注意：配置位已经在程序中写明，加载HEX文件时会自动加载，烧写时不用再手动设置配置位。 实验时请注意套件跳线选择；-pic