E2PROM芯片24C02的读写程序，供参考

基于C8051F020单片机的LCD显示程序，LCD用的是320×240屏幕，驱动芯片为SED1330，采用C51编写-C8051F020 LCD display program, using the LCD 320 x 240 screen, driver chips for SED1330, prepared using C51

small rtos for avr small rtos 使用了动态堆栈 想无需任何改动就可以编译这个程序，就必须安装winavr20050214和uv2,先点击uv2的工程文件打开这个工程然后在Tools---->Customize Tools Menu...嵌入gcc编译命令make all和make clean即可立即编译。编译后可以使用avr studio进行代码级仿真-small Byelorussian for avr small Byelorussian use of dynamic stack without any changes to be compiled for the process, it must be installed and uv2 winavr20050214, first click uv2 works documents before the project opened in Tools- gt; Customize Tools Menu ... embedded gcc compiler make all orders and instantly make clean compile. Compiled avr studio can be used for code-level simulation

ucos的PPT课件 基本原理及其在9s12单片机上怎样移植-OUT PPT Courseware the basic principle and the 9s12 on how to transplant MCU

基于mega64的lcd1602驱动，大家可以看下，互相参考-Mega64 based on the lcd1602 drive, we can facie, be used as a reference

单片机最小系统，使用液晶显示，能够读取键盘值，具有综合扩展功能-The smallest single-chip system, the use of liquid crystal display, the keyboard can read the value of a comprehensive expansion of functions

汉字取模软件 典试用版！喜爱单片机的朋友，下了试试就知道是好东东了！-Chinese Character Code modulus beta software! Singlechip favorite friend, a try to know a good Dongdong!

：介绍一种无人值守的停车场管理系统的设计。该系统前端主要由GsM 短信模块TC35i和AVR 单片机At― megal6组成，安装在停车场的每个进出口，通过接收车主的手机短信控制进出口道闸的开启并由短信扣取停车费用，各进出 口电路都与监控中心计算机连接。-: A unmanned car park management system design. The system front-end GsM messages by AVR module TC35i and At-megal6 composed of single-chip installed in the parking lot of each import or export through SMS to receive the owner to control the import and export of道闸open parking fees deducted by SMS , the import and export of circuits are connected with the monitoring center computer.

AT89C5131的接口驱动-AT89C5131 Driver Interface

该文档包含了keilc常用的子程序，共有２５个运算类代码，非常实用．-This document contains commonly used keilc subprogram, a total of 25 computing category code, very useful.

程序描述：这个范例说明如何使用8051，以及汇编语言的程序连结， 当我们按下向上数的按钮之后，程序就会把0到9的共 阳7段显示器字型码存入AT93C46；如果我们按下向下 数的按钮之后，程序就会把9到0的共阳7段显示器字 型码存入AT93C46。 程序每一次重新开始执行时(Power on 或是Reset)，8051 会先从AT93C46当中读出最前面的10个位组，然后 就反复地将这10个位组的数据经由PORT 1送到1个 共阳七段显示器。*/-Procedure Description: This example shows how to use the 8051, as well as links to assembly language programs, when we pressed up a few of the button, the program will bring a total of 0-9 yang seven segment display font yards into AT93C46 if we press Next down the number button, the program will bring a total of 9-0 Yang seven segment display font code into AT93C46. Process to begin again each time when the (Power on or Reset), 8051 will start with AT93C46 were read out in front, 10-bit groups, and then repeated these 10-bit groups of data via the PORT 1 sent to a A total of seven-segment display Yang.* /