use of software simulation I2C EEPROM communications with the subroutine

日立H8/300H Tiny、H8/3664系列单片机编程 日立H8/3664系列单片机是使用H8/300H高速处理器并以其为核心设计的单片机，为了配置一个系统需要许多外部功能模块。H8/300H高速处理器使用与H8/300处理器兼容的指令系统。 日立H8/3664系列单片机有4个定时器，一个 总线接口，两种不同类型的串行总线 接口，一个A/D转换器，一组I/0接口。本产品适用于高级控制系统的嵌入式应用。 日立H8/300H Tiny 系列（H8/3664系列）使用说明书包含了一组使用H8/3664系列单片机外部功能的具体实例，可供用户在设计硬件及软件产品时参考。-Hitachi H8/300H Tiny, Series H8/3664 H8/3664 microcontroller programming Hitachi microcontroller series is the use of high-speed H8/300H and subject to the processor core microcontroller design, in order to configure a system needs many external modules. H8/300H use of high-speed processors H8/300 processor compatible with the directive system. Hitachi H8/3664 microcontroller series with four timer, a bus interface, two different types of serial bus interface, an A/D converter, a group I/0 interface. This product applies to senior control systems embedded applications. Hitachi H8/300H Tiny series (H8/3664 Series) instruction manual contains a team to use H8/3664 Series MCU external function of spe

此程序为16位Flash擦除烧写的程序实例,可以在51和avr下的c语言跑通-this procedure to erase 16 Flash burning examples of procedures, and 51 avr in the run-language c

收录了许多51单片机的汇编程序，完全可以用于移植开发。同时，也对51学习者进行学习提供了很好的学习教材。

rs485单线程数据通讯程序，KEY键触发能使单片机之间能够通讯-rs485 data communications single-threaded process, KEY key trigger enable communication between the single-chip

PWM控制输出电压由于该程序所需完成的功能比较简单，设计时采用了简单的前后台组织结构：后台程序（主程序）在非通讯状态时工作，完成各项数据的采集和预处理，并标准化至通讯协议所规定的格式。这一过程不停进行，随时提供最新数据；前台程序（中断服务程序）在接收到来自控制器的命令时启动。它对命令加以识别，并按要求向控制器传送相应数据或对数据进行解析执行。该程序的流程示意如图-PWM output voltage control due to the completion of the procedures required for the function of a relatively simple design, a simple organizational structure around Taiwan : background (main program) in non-state communication, complete data acquisition and pre-processing, and standardized communication protocol to the format provided. This process conducted on a continuous basis and provide the latest information; Prospects (interrupt service routine) from the receiving controller to activate the orders. It ordered to be identified, together with a request to the controller or corresponding data transmission for data analysis implementation. The indicative of processes figure

笔段式lcd显示子程序，c语言编写-T-piece lcd display

利用串口和单片机进行通讯,VC用对话框实现-use serial communication and microcontroller, the VC using Dialog

从RS232到PROFIBUS-DP的转换接口设计（终）.rar-from RS232 to PROFIBUS-DP Interface Design (end). Rar

一个LCD菜单绘图程序，通过点阵显示图片，也可显示动态图象！-An LCD menu drawing procedures, through the dot-matrix display images, dynamic images can also be displayed!

KeilC51调试命令大全-KeilC51 commands Daquan