12864的汉字驱动程序，里面包含了一个KEIL工程，可以直接编译...

用C实现信号发生装置：1、正弦波：频率、幅度可调。 2、三角波：频率、幅度可调。 3、方 波：频率、幅度、占空比可调。 4、按键：波形切换、频率调节、幅度调节、方波占空比调节。 5、显示：信号的频率、幅度，在方波时还要显示占空比。 -Implementation using C Signal: 1, sine wave: frequency, amplitude adjustable. 2, triangle-wave: frequency, amplitude adjustable. 3, square wave: the frequency, amplitude, duty cycle adjustable. 4, button: switch waveform, frequency regulation, rate regulation, adjust the duty cycle square wave. 5, show that: the signal frequency, amplitude, when they showed at the duty cycle square wave.

单片机学习的好资料，希望能帮助到需要的朋友-Single-chip learning good information, hoping to help a friend in need

keil c51编写的TLC549驱动函数，经过了测试的-keil c51 ?嘈

2片显示驱动芯片HT1622的C51底层程序-two display driver chip HT1622 the bottom procedures C51

.Is not a sourcecode or document 3.lost some files 4.Description is not detailed or not correct 5.Compressed file has password 6.Sourcecode duplicate

该头文件配合key.c，在main函数中调用key.c，都文件中添加key.h，使软件更清晰，一目了然-The header file with key.c, in the main function call key.c, all files add key.h, so that software is more clear at a glance

基于PSoC+CY8C24533+的电动自行车控制器的设计.rar-Based on PSoC+ CY8C24533+ electric bicycle controller design. Rar

该代码包介绍了基于51系列单片机平台是实现时间触发的嵌入式系统的各种应用的代码-the code based on the Series 51 platform SCM is the time to trigger the Embedded System Applications code

=== =时钟20:6=== === == 应先初始化状态寄存器 tx1714 EQU 7FFH PA EQU 05H PB EQU 06H PC EQU 07H PD EQU 20H IAR EQU 00H 间接寻址寄存器 TMR0 EQU 01H 定时器 STATUS EQU 03H 状态寄存器 BSR EQU 04H bank选择寄存器 PORTA EQU 05H I/0端口寄存器 PORTB EQU 06H I/0端口寄存器 PORTC EQU 07H I/0端口寄存器 PORTD EQU 20H I/0端口寄存器 PULL EQU 21H PULL-High上拉寄存器 WAKEUP EQU 22H 唤醒控制寄存器－－被用来设定watchdog允许和禁止 IRQM EQU 23H 中断屏蔽寄存器 IRQF EQU 24H 中断标志寄存器 WDTSEL EQU 25H -=== === = clock 20 : 6 === === === == should first register initialization state tx1714 EQU 7FFH EQU PA PB EQU 05H 06H 07H PC EQU PD EQU 20H IAR E QU 00H indirectly addressable registers TMR0 EQU 01H timer STATUS EQU Mr send state BSR EQU-deposit bank in the 04H choice Register PORTA EQU 05H I/O ports Register P ORTB EQU 06H I/O ports Register PORTC EQU 07H I/O ports Register POR TD EQU 20H I/O ports Register PULL EQU 21H PULL-High pull Register WAKEUP EQU 22H awaken control registers-- were used to set watchdog allowed and prohi

单片机直接驱动液晶模块, 可以值得大家参考一下-MCU directly drive LCD module may be worthwhile for your reference